Medium Attachment Unit

Not to be confused with Media Access Unit.

A thicknet MAU. The vampire tap on this specimen is still attached to a piece of "frozen yellow garden hose" 10BASE5 network cable, which has been cut.

A thinnet MAU, showing a single BNC and a DA15 connector.

Two Medium Attachment Units, or transceivers. (The units shown are backwards compatibility-oriented 10BASET MAUs, not older 10BASE5 or 10BASE2 MAUs; cf. article.)

A collection of old Ethernet equipment. At the top of the image, from left to right: A thinnet MAU with passthrough BNC connectors and a DA15 connector, a thicknet MAU with passthrough N connectors and a DA15 connector, and an AUI cable for connection of a MAU to the DA15 port on a network card.

A 16-bit ISA network card engineered for compatibility with existing equipment. It includes both an AUI for connection to an external MAU (of any type) and its own MAU-type circuitry integrated on the board, which it uses in case of direct connection of thinnet cable to its BNC connector or twisted-pair cable to its 8P8C connector.

A Medium Attachment Unit (MAU) is a transceiver which converts signals on an Ethernet cable to and from Attachment Unit Interface (AUI) signals.

On original 10BASE5 (Thick) Ethernet equipment, the MAU was typically clamped to the Ethernet wire and multi-wire cable-connected to the computer via a DA-15 port, which was also what was present on the NIC. With later standards, thicknet vampire taps gave way to BNC connectors (for thinnet coax cables) and 8P8C connectors (for twisted-pair cables). MAUs for these still connected to NICs via DA-15 cables, but soon the MAU ceased to be a separate adapter and was generally integrated into the network interface controller. Eventually the entire Ethernet controller was often integrated into a single integrated circuit ("chip") to reduce cost.

In most modern switched or hubbed Ethernet over twisted pair systems, neither the MAU nor the AUI interfaces exist (apart, perhaps as notional entities for the purposes of thinking about layering the interface), and the category 5 (CAT5) or better cable connects directly into an Ethernet socket on the host or router. For backwards compatibility with equipment which still had external AUI interfaces only, adapter-type MAUs with 10BASE2 or 10BASE-T connectors long remained available after the obsolescence of original vampire-tap MAUs, but even adapter-type MAUs have become very rare as of the 2020s.

Similar equipment

The original Ethernet's successor standard, Fast Ethernet, introduced division onto media access control (MAC) and physical (PHY) layers connected with media-independent interface (MII). Some early Fast Ethernet hardware had physical external MII connectors, functionally similar to AUI connector, but generally separate adaptors got obsoleted, see above. However, the tradition of using a separate low-level I/O device in networking has continued in fast optical fiber network interfaces, where the GBIC, XENPAK, XFP, and enhanced small form-factor pluggable (SFP+) pluggable transceiver modules using the XAUI interface play a similar role.

Objectives of MAUs

• Provide the physical means for communication between local network data link entities.
• It defines a physical interface that can be implemented independently among different manufacturers of hardware and achieve the intended level of compatibility when interconnected in a common local network.
• Provide a communication channel capable of high bandwidth and low bit error ratio performance.
• Provide for ease of installation and service.
• Provide for high network availability (ability of a station to gain access to the medium and enable the data link connection in a timely fashion).
• Enable relatively low-cost implementations.

MAU Characteristics

• Enables coupling the Physical Layer Signalling (PLS) by way of the AUI to the explicit baseband coaxial transmission system.
• Supports message traffic at a data rate of 10, 100, or even 1000 Mbit/s.
• Provides for driving up to 500m of coaxial trunk cable without the use of a repeater.
• Permits the DTE to test the MAU and the medium itself.
• Supports system configurations using the CSMA/CD access mechanism defined with baseband signaling.
• Supports bus topology interconnection.

Services provided by MAUs

• Transmit.
• Receive.
• Collision detection and Loop-back functions direct transfer through the MAU.
• The Jabber detect.
  • It removes equipment from the network whenever it continuously transmits for periods significantly longer than required for a maximum-length packet, indicating a possible problem with the NIC.
• Signal quality error test.
  • The signal quality error test detects silent failures in the circuitry.
• Link integrity functions
  • detects breaks in the wire pairs.
• Both Signal quality error test and Link integrity functions assist in fault isolation.

Two modes of operation

• Normal mode:
  • The MAU functions as a direct connection between the baseband medium and the DTE. Data output from the DTE is output to the coaxial trunk medium and all data on the coaxial trunk medium is input to the DTE. This mode is the "normal" mode of operation for the intended message traffic between stations.
• Monitor mode or Isolated mode:
  • The MAU functions as a receive-only connection between the baseband medium and the DTE. Data output from the DTE is suppressed and only data on the coaxial trunk medium is input to the DTE. This mode is for observing message traffic.

MAU functional specifications

• Transmit function
  • The ability to transmit serial data bit streams on the baseband medium from the local DTE entity and to one or more remote DTE entities on the same network.
• Receive function
  • The ability to receive serial data bit streams over the baseband medium.
• Collision Presence function
  • The ability to detect the presence of two or more stations concurrent transmissions.
• Monitor function (Optional)
  • The ability to inhibit the normal transmit data stream to the medium at the same time the normal receive function and collision presence function remain operational.
• Jabber function
  • The ability to automatically interrupt the transmit function and inhibit an abnormally long output data stream. It removes equipment from the network whenever it continuously transmits for periods significantly longer than required for a maximum-length packet, indicating a possible problem with the NIC.

References

• "IEEE Standard for Information technology— Telecommunications and information exchange between systems— Local and metropolitan area networks— Specific requirements Part 3: Carrier sense multiple access with Collision Detection (CSMA/CD) Access Method and Physical Layer Specifications". IEEE Standard. IEEE.