STM8
 | This article needs additional citations for verification. (January 2018) |
The STM8 is an 8-bit microcontroller family by STMicroelectronics. The STM8 microcontrollers use an extended variant of the ST7 microcontroller architecture. STM8 microcontrollers are particularly low cost for a full-featured 8-bit microcontroller.[1]
Architecture[edit]
The STM8 is very similar to the earlier ST7, but is better suited as a target for C due to its 16-bit index registers and stack pointer-relative addressing mode. Although internally a Harvard architecture it has "memory bridge" that creates a unified 24-bit address space, allowing code to execute out of RAM (useful for in-system programming of the flash ROM), and data (such as lookup tables) to be accessed out of ROM. On access the "memory bridge" stalls the CPU if required so that RAM-like write access to the flash ROM is possible. Code execution from the EEPROM is denied and creates a reset event. Random access to data above 64K is limited to special "load far" instructions; most operations' memory operands can access at most 128K (a 16-bit base address plus 16-bit offset).
Depending on the device type, the amount of RAM is in the range of 1 to 6 KiB, and the amount of ROM is 4 to 8 KiB (Low density), 16 to 32 KiB (Medium density), or 32 to 96 KiB (High density).
It has the same six registers (A, X, Y, SP, PC, CC) as the ST7, but the index registers X and Y have been expanded to 16 bits, and the program counter has been expanded to 24 bits. The accumulator A and the stack pointer remain 8 and 16 bits, respectively.[2]
The condition code register has two more defined bits, for a total of seven. There is an overflow flag, and a second interrupt enable bit, allowing four interrupt priority levels.
Subfamilies[edit]
- STM8AF automobile
- STM8AL automobile low-power
- STM8L low-power
- STM8S general purpose
- STM8T touch-sensing
- STLUX lighting control
- STNRG Pulse-width modulation-controllers
Compiler support[edit]
The STM8 is supported by the free Small Device C Compiler, the free of charge closed source Cosmic C compiler,[3] and the non-free IAR C and Raisonance compilers. Besides C there is the open-source STM8 eForth,[4] an interactive Forth system for the STM8.
Changes compared to ST7[edit]
The STM8 instruction set is mostly a superset of the ST7's, but it is not completely binary compatible.
Operations on the X and Y registers are extended to 16 bits. Thus, loads and stores access two bytes of memory rather than one. (Also, the half-carry flag has been changed to reflect the carry from bit 7 to bit 8 of the 16-bit result, rather than the carry from bit 3 to 4.)
Interrupts push nine bytes of state instead of five as on the ST7.
The multiply instruction stores the 16-bit product in the specified index register (e.g. X), rather than dividing it between X and A.
Indirect addressing modes which fetch an 8-bit address from memory (opcodes 92 2x, 92 3x, 92 Bx, 92 6x, 92 Ex, 91 6x, and 91 Ex) have been deleted; all indirect addressing modes fetch 16-bit addresses. A new prefix byte 72 has been added, and used to encode indirect starting with a 16-bit address.
The bit manipulation instructions have been changed to take a 16-bit address and to require the 72 prefix byte. The unprefixed opcodes 0x and 1x they formerly occupied are instead used for stack-pointer relative addressing.
Some rarely used branch instructions have had their opcodes changed to require a 90 prefix, and the unprefixed opcodes reassigned to signed branches which depend on the V flag.
Load and compare instructions targeting the X register are of little use on the ST7 with addressing modes indexed by the X register. On the STM8, when such operations specify a memory operand indexed by the X register, the register operand is changed to Y. With a 90 prefix, the registers are reversed so the index register is Y and the operand register is X.
One major performance difference is that the STM8 fetches 32 bits from ROM per cycle, and many instructions take one cycle to execute. Depending in the instruction length and the number of cycles needed execution from RAM is somewhat slower. The ST7, in contrast, fetches 8 bits per cycle and takes one cycle per instruction byte.
Instruction set[edit]
Most STM8 opcode bytes consist of 1 bit of type (one- or two-operand), three bits of addressing mode, and four bits of opcode. Only 6 addressing modes and 12 one-operand opcodes are assigned, leaving encoding space where other instructions are placed.
| 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | Description |
|---|---|---|---|---|---|---|---|---|
| 0 | mode | opcode | One-operand instructions (mode ≠ 1, 2) | |||||
| 0 | 0 | 0 | 1 | opcode | Additional two-operand instructions | |||
| 0 | 0 | 1 | 0 | opcode | Conditional branches | |||
| 0 | opcode | 0 | 0 | 0 | 1 | Other arithmetic instructions (opcode ≠ 1, 2) | ||
| 0 | opcode | 0 | 0 | 1 | 0 | |||
| 0 | opcode | 0 | 1 | 0 | 1 | |||
| 0 | opcode | 1 | 0 | 1 | 1 | |||
| 1 | mode | opcode | Two-operand instructions (mode ≠ 0, 1) | |||||
| 1 | 0 | 0 | opcode | Miscellaneous non-arithmetic instructions | ||||
STM8 instructions consist of an optional prefix byte (7216, 9016, 9116, or 9216), an opcode byte, and a few (up to four, but rarely more than two) bytes of operands. Prefix bytes mostly modify the addressing mode used to specify the memory operand, but in some cases, prefixes 72 and 90 change the meaning of the opcode byte completely.
Prefix 90 exchanges X and Y in the following instruction. In the table below, these variants are combined on one line by writing "X/Y", which means either "X" or "Y". Prefix 90 is also used in two places to introduce new opcodes: the BCPL and BCCM instructions, and some branch conditions.
Prefix 92 converts instructions with an offset operand (addr16,X) to indirect addressing ([addr8],X). The offset is replaced by the 8-bit address of a 16-bit offset value in memory. It is used only for this function.
Prefix 91 has both of the preceding effects, converting (addr16,X) addressing modes to ([addr8],Y).
Prefix 72 is used in a number of places, in a much less regular pattern. In some cases, it introduces new addressing modes (particularly an ([addr16],X) 16-bit indirect mode), but it also introduces many completely new operations.
| Prefix | 7 | 6 | 5 | 4 | 3 | 2 | 1 | 0 | Operands | Mnemonic | Description |
|---|---|---|---|---|---|---|---|---|---|---|---|
| — | 0 | 0 | 0 | 0 | opcode | addr8 | OP (addr8,SP) | One-operand instructions (see below) | |||
| — | 0 | 0 | 0 | 1 | opcode | addr8 | OP A,(addr8,SP) | Two-operand instructions with stack operand | |||
| — | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | addr8 | SUB A,(addr8,SP) | A := A − operand |
| — | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 1 | addr8 | CP A,(addr8,SP) | Compare A − operand |
| — | 0 | 0 | 0 | 1 | 0 | 0 | 1 | 0 | addr8 | SBC A,(addr8,SP) | A := A − operand − C subtract with borrow |
| — | 0 | 0 | 0 | 1 | 0 | 0 | 1 | 1 | addr8 | CPW X,(addr8,SP) | Compare X − operand (16-bit) |
| — | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 0 | addr8 | AND A,(addr8,SP) | A := A & operand, bitwise and |
| — | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | addr8 | BCP A,(addr8,SP) | Bitwise test A & operand |
| — | 0 | 0 | 0 | 1 | 0 | 1 | 1 | 0 | addr8 | LDW Y,(addr8,SP) | Y := operand ( |
| — | 0 | 0 | 0 | 1 | 0 | 1 | 1 | 1 | addr8 | LDW (addr8,SP),Y | Operand := Y ( |
| — | 0 | 0 | 0 | 1 | 1 | 0 | 0 | 0 | addr8 | XOR A,(addr8,SP) | A := A ^ operand, exclusive-or |
| — | 0 | 0 | 0 | 1 | 1 | 0 | 0 | 1 | addr8 | ADC A,(addr8,SP) | A := A + operand + C, add with carry |
| — | 0 | 0 | 0 | 1 | 1 | 0 | 1 | 0 | addr8 | OR A,(addr8,SP) | A := A | operand, inclusive or |
| — | 0 | 0 | 0 | 1 | 1 | 0 | 1 | 1 | addr8 | ADD A,(addr8,SP) | A := A + operand |
| — | 0 | 0 | 0 | 1 | 1 | 1 | 0 | 0 | imm16 | ADDW X,#imm16 | X := X + immediate (= |
| — | 0 | 0 | 0 | 1 | 1 | 1 | 0 | 1 | imm16 | SUBW X,#imm16 | X := X − immediate (= |
| — | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 0 | addr8 | LDW X,(addr8,SP) | X := operand |
| — | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | addr8 | LDW (addr8,SP),X | Operand := X |
| 72/90 | 0 | 0 | 0 | c | bit | v | operands | Bit operations | |||
| 72 | 0 | 0 | 0 | 0 | bit | 0 | addr16 soff8 | BTJT addr16,#bit,label | Jump to PC + soff8 if source bit is true (set) | ||
| 72 | 0 | 0 | 0 | 0 | bit | 1 | addr16 soff8 | BTJF addr16,#bit,label | Jump to PC + soff8 if source bit is false (clear) | ||
| 72 | 0 | 0 | 0 | 1 | bit | 0 | addr16 | BSET addr16,#bit | Set specified bit to 1 | ||
| 72 | 0 | 0 | 0 | 1 | bit | 1 | addr16 | BRES addr16,#bit | Reset (clear) specified bit to 0 | ||
| 90 | 0 | 0 | 0 | 1 | bit | 0 | addr16 | BCPL addr16,#bit | Complement (toggle) selected bit | ||
| 90 | 0 | 0 | 0 | 1 | bit | 1 | addr16 | BCCM addr16,#bit | Write carry flag to memory bit | ||
| —/90 | 0 | 0 | 1 | 0 | condition | soff8 | Conditional branches (8-bit signed offset) | ||||
| — | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | soff8 | JRA label | Branch always (true) |
| — | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 1 | soff8 | JRF label | Branch never (false) |
| — | 0 | 0 | 1 | 0 | 0 | 0 | 1 | 0 | soff8 | JRUGT label | Branch if unsigned greater than (C=0 and Z=0) |
| — | 0 | 0 | 1 | 0 | 0 | 0 | 1 | 1 | soff8 | JRULE label | Branch if unsigned less than or equal (C=1 or Z=1) |
| — | 0 | 0 | 1 | 0 | 0 | 1 | 0 | 0 | soff8 | JRNC label | Branch if no carry (C=0) |
| — | 0 | 0 | 1 | 0 | 0 | 1 | 0 | 1 | soff8 | JRC label | Branch if carry (C=1) |
| — | 0 | 0 | 1 | 0 | 0 | 1 | 1 | 0 | soff8 | JRNE label | Branch if not equal (Z=0) |
| — | 0 | 0 | 1 | 0 | 0 | 1 | 1 | 1 | soff8 | JREQ label | Branch if equal (Z=1) |
| — | 0 | 0 | 1 | 0 | 1 | 0 | 0 | 0 | soff8 | JRNV label | Branch if not overflow (V=0) |
| 90 | 0 | 0 | 1 | 0 | 1 | 0 | 0 | 0 | soff8 | JRNH label | Branch if not half-carry (H=0) |
| — | 0 | 0 | 1 | 0 | 1 | 0 | 0 | 1 | soff8 | JRV label | Branch if overflow (V=1) |
| 90 | 0 | 0 | 1 | 0 | 1 | 0 | 0 | 1 | soff8 | JRH label | Branch if half-carry (H=1) |
| — | 0 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | soff8 | JRPL label | Branch if plus (N=0) |
| — | 0 | 0 | 1 | 0 | 1 | 0 | 1 | 1 | soff8 | JRMI label | Branch if minus (N=1) |
| — | 0 | 0 | 1 | 0 | 1 | 1 | 0 | 0 | soff8 | JRSGT label | Branch if signed greater than (S=0 and N=V) |
| 90 | 0 | 0 | 1 | 0 | 1 | 1 | 0 | 0 | soff8 | JRNM label | Branch if not interrupt mask (I=0) |
| — | 0 | 0 | 1 | 0 | 1 | 1 | 0 | 1 | soff8 | JRSLE label | Branch if signed lower or equal (S=1 or N≠V) |
| 90 | 0 | 0 | 1 | 0 | 1 | 1 | 0 | 1 | soff8 | JRM label | Branch if interrupts masked (I=1) |
| — | 0 | 0 | 1 | 0 | 1 | 1 | 1 | 0 | soff8 | JRSGE label | Branch if signed greater or equal (N=V) |
| 90 | 0 | 0 | 1 | 0 | 1 | 1 | 1 | 0 | soff8 | JRIL label | Branch if interrupt line is low |
| — | 0 | 0 | 1 | 0 | 1 | 1 | 1 | 1 | soff8 | JRSLT label | Branch if signed less than (N≠V) |
| 90 | 0 | 0 | 1 | 0 | 1 | 1 | 1 | 1 | soff8 | JRIH label | Branch if interrupt line is high |
| prefix | 0 | mode | opcode | operand | One-operand instructions | ||||||
| — | 0 | 0 | 0 | 0 | opcode | addr8 | OP (addr8,SP) | Stack pointer relative | |||
| 0 | 0 | 0 | 1 | opcode | (reassigned to two-operand instructions with stack; see above) | ||||||
| 0 | 0 | 1 | 0 | opcode | (reassigned to conditional branches; see above) | ||||||
| — | 0 | 0 | 1 | 1 | opcode | addr8 | OP addr8 | 8-bit absolute address | |||
| 72 | 0 | 0 | 1 | 1 | opcode | addr16 | OP [addr16] | 16-bit indirect address | |||
| 92 | 0 | 0 | 1 | 1 | opcode | addr8 | OP [addr8] | 8-bit indirect address of 16-bit address | |||
| — | 0 | 1 | 0 | 0 | opcode | — | OP A | Accumulator | |||
| 72/90 | 0 | 1 | 0 | 0 | opcode | addr16 | OP (addr16,X/Y) | Indexed with 16-bit offset | |||
| —/90 | 0 | 1 | 0 | 1 | opcode | — | OPW X/Y | X/Y register (16-bit operation) | |||
| 72 | 0 | 1 | 0 | 1 | opcode | addr16 | OP addr16 | 16-bit address | |||
| —/90 | 0 | 1 | 1 | 0 | opcode | addr8 | OP (addr8,X/Y) | 8-bit address plus X/Y | |||
| 72 | 0 | 1 | 1 | 0 | opcode | addr16 | OP ([addr16],X) | 16-bit indirect address plus X | |||
| 92/91 | 0 | 1 | 1 | 0 | opcode | addr8 | OP ([addr8],X/Y) | 8-bit indirect address plus X/Y | |||
| —/90 | 0 | 1 | 1 | 1 | opcode | — | OP (X/Y) | Indexed with no offset | |||
| prefix | 0 | mode | 0 | 0 | 0 | 0 | operand | NEG operand | Two's-complement negate | ||
| 0 | mode | 0 | 0 | 0 | 1 | (reassigned to exchange operations; see following section) | |||||
| 0 | mode | 0 | 0 | 1 | 0 | (reassigned to other operations; see following section) | |||||
| prefix | 0 | mode | 0 | 0 | 1 | 1 | operand | CPL operand | Ones' complement, logical not | ||
| prefix | 0 | mode | 0 | 1 | 0 | 0 | operand | SRL operand | Shift right logical, msbit cleared, lsbit to carry: (operand:C) := (0:operand) | ||
| 0 | mode | 0 | 1 | 0 | 1 | (reassigned to other operations; see following section) | |||||
| prefix | 0 | mode | 0 | 1 | 1 | 0 | operand | RRC operand | Rotate right through carry, (operand:C) := (C:operand) | ||
| prefix | 0 | mode | 0 | 1 | 1 | 1 | operand | SRA operand | Shift right arithmetic, msbit preserved, lsbit to carry | ||
| prefix | 0 | mode | 1 | 0 | 0 | 0 | operand | SLL operand | Shift left, msbit to carry: (C:operand) := (operand:0) | ||
| prefix | 0 | mode | 1 | 0 | 0 | 1 | operand | RLC operand | Rotate left through carry, (C:operand) := (operand,C) | ||
| prefix | 0 | mode | 1 | 0 | 1 | 0 | operand | DEC operand | Decrement; N and Z set, carry unaffected | ||
| 0 | mode | 1 | 0 | 1 | 1 | (reassigned to other operations; see following section) | |||||
| prefix | 0 | mode | 1 | 1 | 0 | 0 | operand | INC operand | Increment; N and Z set, carry unaffected | ||
| prefix | 0 | mode | 1 | 1 | 0 | 1 | operand | TNZ operand | Test non-zero: set N and Z based on operand value | ||
| prefix | 0 | mode | 1 | 1 | 1 | 0 | operand | SWAP operand | Swap halves of operand (4-bit rotate; 8-bit for SWAPW X and SWAPW Y) | ||
| prefix | 0 | mode | 1 | 1 | 1 | 1 | operand | CLR operand | Set operand to 0, N cleared, Z set | ||
| prefix | 0 | mode | opcode | operand | Reassigned opodes [03-7][125B] from one-operand range | ||||||
| —/90 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | — | RRWA X/Y | Rotate word right through A: 8-bit right rotate of 24-bit concatenation of X/Y and A; (X:A) := (A:X) |
| — | 0 | 0 | 1 | 1 | 0 | 0 | 0 | 1 | addr16 | EXG A,addr16 | Exchange A with memory |
| — | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 1 | — | EXG A,XL | Exchange A with X (low half) |
| — | 0 | 1 | 0 | 1 | 0 | 0 | 0 | 1 | — | EXGW X,Y | Exchange X with Y (16 bits) |
| — | 0 | 1 | 1 | 0 | 0 | 0 | 0 | 1 | — | EXG A,YL | Exchange A with Y (low half) |
| — | 0 | 1 | 1 | 1 | 0 | 0 | 0 | 1 | — | (reserved) | |
| —/90 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | — | RLWA X/Y | Rotate word left through A: 8-bit left rotate of 24-bit concatenation of X/Y and A; (A:X) := (X:A) |
| — | 0 | 0 | 1 | 1 | 0 | 0 | 1 | 0 | addr16 | POP addr16 | Pop from stack |
| —/90 | 0 | 1 | 0 | 0 | 0 | 0 | 1 | 0 | — | MUL X/Y,A | X/Y := XL/YL × A |
| — | 0 | 1 | 0 | 1 | 0 | 0 | 1 | 0 | imm8 | SUBW SP,#imm | SP := SP − imm8 |
| —/90 | 0 | 1 | 1 | 0 | 0 | 0 | 1 | 0 | — | DIV X/Y,A | Divide X/Y by A; 16-bit quotient in X/Y, remainder in A |
| — | 0 | 1 | 1 | 1 | 0 | 0 | 1 | 0 | — | PREFIX | Instruction prefix 72: modify following opcode
|
| 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | — | (reserved) | ||
| — | 0 | 0 | 1 | 1 | 0 | 1 | 0 | 1 | imm8 addr16 | MOV addr16,#imm8 | Move immediate to memory (flags unaffected) |
| — | 0 | 1 | 0 | 0 | 0 | 1 | 0 | 1 | addr8 addr8 | MOV addr8,addr8 | Move memory to memory (flags unaffected) |
| — | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 | addr16 addr16 | MOV addr16,addr16 | Move memory to memory (flags unaffected) |
| — | 0 | 1 | 1 | 0 | 0 | 1 | 0 | 1 | — | DIVW X,Y | Divide X by Y (16 bits); quotient in X, remainder in Y |
| 0 | 1 | 1 | 1 | 0 | 1 | 0 | 1 | — | (reserved) | ||
| 0 | 0 | 0 | 0 | 1 | 0 | 1 | 1 | — | (reserved) | ||
| — | 0 | 0 | 1 | 1 | 1 | 0 | 1 | 1 | addr16 | PUSH addr16 | Push onto stack |
| — | 0 | 1 | 0 | 0 | 1 | 0 | 1 | 1 | imm8 | PUSH #imm8 | Push onto stack |
| — | 0 | 1 | 0 | 1 | 1 | 0 | 1 | 1 | imm8 | ADDW SP,#imm8 | SP := SP + imm8 |
| — | 0 | 1 | 1 | 0 | 1 | 0 | 1 | 1 | addr8 | LD (addr8,SP),A | Store relative to stack |
| — | 0 | 1 | 1 | 1 | 1 | 0 | 1 | 1 | addr8 | LD A,(addr8,SP) | Load relative to stack |
| — | 1 | 0 | 0 | opcode | — | Miscellaneous instructions. None implicitly set the condition codes. | |||||
| — | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | — | IRET | Return from interrupt (pop CC, A, X, Y, PC) |
| — | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | — | RET | Pop 16-bit return address from stack to PC |
| — | 1 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | addr24 | INT | Special jump for interrupt vector table |
| — | 1 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | — | TRAP | Force trap interrupt |
| — | 1 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | — | POP A | Pop A from stack |
| —/90 | 1 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | — | POPW X/Y | Pop X/Y from stack (16 bits) |
| — | 1 | 0 | 0 | 0 | 0 | 1 | 1 | 0 | — | POP CC | Pop condition codes from stack |
| — | 1 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | — | RETF | Pop 24-bit return address from stack to PC |
| — | 1 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | — | PUSH A | Push A onto stack |
| —/90 | 1 | 0 | 0 | 0 | 1 | 0 | 0 | 1 | — | PUSHW X/Y | Push X/Y onto stack (16 bits) |
| — | 1 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | — | PUSH CC | Push condition codes onto stack |
| — | 1 | 0 | 0 | 0 | 1 | 0 | 1 | 1 | — | BREAK | Stop for debugger if present, or NOP |
| — | 1 | 0 | 0 | 0 | 1 | 1 | 0 | 0 | — | CCF | Complement (toggle) carry flag |
| — | 1 | 0 | 0 | 0 | 1 | 1 | 0 | 1 | addr24 | CALLF addr24 | Push 24-bit PC; PC := addr24 |
| 92 | 1 | 0 | 0 | 0 | 1 | 1 | 0 | 1 | addr16 | CALLF [addr16] | Indirect far call; address is of 24-bit pointer |
| — | 1 | 0 | 0 | 0 | 1 | 1 | 1 | 0 | — | HALT | Halt processor and clocks |
| — | 1 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | — | WFI | Wait for interrupt, halting processor but not clocks |
| 72 | 1 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | — | WFE | Wait for event (coprocessor), handling interrupts normally while waiting |
| — | 1 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | — | PDY | Instruction prefix 90: swap X and Y in next instruction
|
| — | 1 | 0 | 0 | 1 | 0 | 0 | 0 | 1 | — | PIY | Instruction prefix 91: PDY plus PIX
|
| — | 1 | 0 | 0 | 1 | 0 | 0 | 1 | 0 | — | PIX | Instruction prefix 92: use 8-bit memory indirect for operand
|
| —/90 | 1 | 0 | 0 | 1 | 0 | 0 | 1 | 1 | — | LDW X/Y,Y/X | X/Y := Y/X |
| —/90 | 1 | 0 | 0 | 1 | 0 | 1 | 0 | 0 | — | LDW SP,X/Y | SP := X/Y |
| —/90 | 1 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | — | LD XH/YH,A | XH/YH := A |
| —/90 | 1 | 0 | 0 | 1 | 0 | 1 | 1 | 0 | — | LDW X/Y,SP | X/Y := SP |
| —/90 | 1 | 0 | 0 | 1 | 0 | 1 | 1 | 1 | — | LD XL/YL,A | XL/YL := A |
| — | 1 | 0 | 0 | 1 | 1 | 0 | 0 | 0 | — | RCF | Reset (clear) carry flag |
| — | 1 | 0 | 0 | 1 | 1 | 0 | 0 | 1 | — | SCF | Set carry flag |
| — | 1 | 0 | 0 | 1 | 1 | 0 | 1 | 0 | — | RIM | Reset interrupt mask (enable interrupts) |
| — | 1 | 0 | 0 | 1 | 1 | 0 | 1 | 1 | — | SIM | Set interrupt mask (disable interrupts) |
| — | 1 | 0 | 0 | 1 | 1 | 1 | 0 | 0 | — | RVF | Reset (clear) overflow flag |
| — | 1 | 0 | 0 | 1 | 1 | 1 | 0 | 1 | — | NOP | No operation |
| —/90 | 1 | 0 | 0 | 1 | 1 | 1 | 1 | 0 | — | LD A,XH/YH | A := XH/YH |
| —/90 | 1 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | — | LD A,XL/YL | A := XL/YL |
| Prefix | 1 | mode | opcode | operand | Two-operand instructions A := A op operand | ||||||
| — | 0 | 0 | 0 | 0 | opcode | addr8 | OP A,(addr8,SP) | (opcodes 6, 7, C, D differ; see above) | |||
| — | 1 | 0 | 0 | opcode | (reassigned to miscellaneous instructions; see above) | ||||||
| — | 1 | 0 | 1 | 0 | opcode | imm8 | OP A,#imm8 | 8-bit immediate operand (forbidden as destination) | |||
| — | 1 | 0 | 1 | 1 | opcode | addr8 | OP A,addr8 | 8-bit absolute address (forbidden for jump/call) | |||
| — | 1 | 1 | 0 | 0 | opcode | addr16 | OP A,addr16 | 16-bit absolute address | |||
| 72 | 1 | 1 | 0 | 0 | opcode | addr16 | OP A,[addr16] | 16-bit indirect address | |||
| 92 | 1 | 1 | 0 | 0 | opcode | addr8 | OP A,[addr8] | 8-bit indirect address of 16-bit address | |||
| —/90 | 1 | 1 | 0 | 1 | opcode | addr16 | OP A,(addr16,X/Y) | Indexed with 16-bit offset | |||
| 72 | 1 | 1 | 0 | 1 | opcode | addr16 | OP A,([addr16],X) | 16-bit indirect + X | |||
| 92/91 | 1 | 1 | 0 | 1 | opcode | addr16 | OP A,([addr8],X/Y) | 8-bit indirect + X/Y | |||
| —/90 | 1 | 1 | 1 | 0 | opcode | addr8 | OP A,(addr8,X/Y) | Indexed with 8-bit offset | |||
| —/90 | 1 | 1 | 1 | 1 | opcode | — | OP A,(X/Y) | Indexed with no offset | |||
| prefix | 1 | mode | 0 | 0 | 0 | 0 | operand | SUB A,operand | A := A − operand | ||
| prefix | 1 | mode | 0 | 0 | 0 | 1 | operand | CP A,operand | Compare A − operand | ||
| prefix | 1 | mode | 0 | 0 | 1 | 0 | operand | SBC A,operand | A := A − operand − C subtract with borrow | ||
| prefix | 1 | mode | 0 | 0 | 1 | 1 | operand | CPW X/Y,operand | Compare X/Y − operand (16 bit); compare Y/X if operand mode is indexed by X/Y (opcodes D3, E3, F3) | ||
| prefix | 1 | mode | 0 | 1 | 0 | 0 | operand | AND A,operand | A := A & operand, bitwise and | ||
| prefix | 1 | mode | 0 | 1 | 0 | 1 | operand | BCP A,operand | Bitwise test A & operand | ||
| prefix | 1 | mode | 0 | 1 | 1 | 0 | operand | LD A,operand | A := operand | ||
| prefix | 1 | mode | 0 | 1 | 1 | 1 | operand | LD operand,A | Operand := A (mode 2 | ||
| prefix | 1 | mode | 1 | 0 | 0 | 0 | operand | XOR A,operand | A := A ^ operand, exclusive-or | ||
| prefix | 1 | mode | 1 | 0 | 0 | 1 | operand | ADC A,operand | A := A + operand + C, add with carry | ||
| prefix | 1 | mode | 1 | 0 | 1 | 0 | operand | OR A,operand | A := A | operand, inclusive or | ||
| prefix | 1 | mode | 1 | 0 | 1 | 1 | operand | ADD A,operand | A := A + operand | ||
| prefix | 1 | mode | 1 | 1 | 0 | 0 | operand | JP operand | Low 16 bits of PC := operand, unconditional jump (modes 2 | ||
| prefix | 1 | mode | 1 | 1 | 0 | 1 | operand | CALL operand | Push 16-bit PC, low 16 bits of PC := operand (modes 2 | ||
| prefix | 1 | mode | 1 | 1 | 1 | 0 | operand | LDW X/Y,operand | Load X/Y := operand; use 16 instead of 90 1E for LDW Y,(addr8,SP) | ||
| prefix | 1 | mode | 1 | 1 | 1 | 1 | operand | LDW operand,X/Y | Operand := X/Y (16-bit, mode 2 | ||
| Prefix | 1 | mode | opcode | operand | Reassigned opcodes A7, AC, BC, AD, BD, AF from two-operand range | ||||||
| —/90 | 1 | 0 | 1 | 0 | 0 | 1 | 1 | 1 | addr24 | LDF (addr24,X/Y),A | Load far (= |
| 92/91 | 1 | 0 | 1 | 0 | 0 | 1 | 1 | 1 | addr16 | LDF ([addr16],X/Y),A | 16-bit address of 24-bit pointer |
| — | 1 | 0 | 1 | 0 | 1 | 1 | 0 | 0 | addr24 | JPF addr24 | PC := addr24 (= |
| 92 | 1 | 0 | 1 | 0 | 1 | 1 | 0 | 0 | addr16 | JPF [addr16] | Indirect far jump; address is of 24-bit pointer |
| — | 1 | 0 | 1 | 1 | 1 | 1 | 0 | 0 | addr24 | LDF A,addr24 | Load far (= |
| 92 | 1 | 0 | 1 | 1 | 1 | 1 | 0 | 0 | addr16 | LDF A,[addr16] | Load far, 16-bit address of 24-bit pointer |
| — | 1 | 0 | 1 | 0 | 1 | 1 | 0 | 1 | soff8 | CALLR label | Push 16-bit PC, PC := PC + operand (= |
| — | 1 | 0 | 1 | 1 | 1 | 1 | 0 | 1 | addr24 | LDF addr24,A | Operand := A (= |
| 92 | 1 | 0 | 1 | 1 | 1 | 1 | 0 | 1 | addr16 | LDF [addr16],A | Operand := A, 16-bit address of 24-bit pointer |
| —/90 | 1 | 0 | 1 | 0 | 1 | 1 | 1 | 1 | addr24 | LDF A,(addr24,X/Y) | Load far (= |
| 92/91 | 1 | 0 | 1 | 0 | 1 | 1 | 1 | 1 | addr16 | LDF A,([addr16],X/Y) | 16-bit address of 24-bit pointer |
| 72 | 1 | mode | opcode | operand | Index register arithmetic (16-bit) X/Y := X/Y ± operand | ||||||
| 72 | 1 | 0 | 1 | 0 | opcode | imm16 | OPW X/Y,#imm16 | 16-bit immediate | |||
| 72 | 1 | 0 | 1 | 1 | opcode | addr16 | OPW X/Y,addr16 | 16-bit absolute | |||
| 72 | 1 | 1 | 1 | 1 | opcode | addr8 | OPW X/Y,(addr8,SP) | Stack-relative | |||
| 72 | 1 | mode | 0 | 0 | 0 | 0 | operand | SUBW X,operand | X := X − operand (prefer opcode 1D for SUBW X,#imm16) | ||
| 72 | 1 | mode | 0 | 0 | 1 | 0 | operand | SUBW Y,operand | Y := Y − operand | ||
| 72 | 1 | mode | 1 | 0 | 0 | 1 | operand | ADDW Y,operand | Y := Y + operand | ||
| 72 | 1 | mode | 1 | 0 | 1 | 1 | operand | ADDW X,operand | X := X + operand (prefer opcode 1C for ADDW X,#imm16) | ||
For CPW and LDW instructions where the operand addressing mode is indexed by X, the STM8 uses the Y register by default instead of X. Applying a 90 prefix exchanges X and Y so the register is X and the addressing mode is indexed by Y.
References[edit]
- ^ Carlson, Jay (September 15, 2017). "ST STM8". Retrieved 2018-06-12.
- ^ a b c "PM0044: STM8 CPU programming manual" (PDF). STMicroelectronics. September 2011. Document 13590 Rev 3. Retrieved 2018-06-10.
- ^ "COS-C-COMPILER - Free C Compiler for all STM8, from Cosmic" (Press release). STMicroelectronics. Retrieved 24 March 2016.
- ^ "STM8 eForth - a user friendly Forth for simple µCs with docs". GitHub. 18 November 2022.