File:Dale Reed with model in front of M2-F1 DVIDS717045.jpg
Page contents not supported in other languages.
Tools
Actions
General
In other projects
Appearance
![File:Dale Reed with model in front of M2-F1 DVIDS717045.jpg](http://upload.wikimedia.org/wikipedia/commons/thumb/6/68/Dale_Reed_with_model_in_front_of_M2-F1_DVIDS717045.jpg/480px-Dale_Reed_with_model_in_front_of_M2-F1_DVIDS717045.jpg)
Size of this preview: 480 × 600 pixels. Other resolutions: 192 × 240 pixels | 384 × 480 pixels | 614 × 768 pixels | 819 × 1,024 pixels | 2,400 × 3,000 pixels.
Original file (2,400 × 3,000 pixels, file size: 528 KB, MIME type: image/jpeg)
![]() | This is a file from the Wikimedia Commons. Information from its description page there is shown below. Commons is a freely licensed media file repository. You can help. |
Summary
DescriptionDale Reed with model in front of M2-F1 DVIDS717045.jpg |
English: Dale Reed with a model of the M2-F1 in front of the actual lifting body. Reed used the model to show the potential of the lifting bodies. He first flew it into tall grass to test stability and trim, then hand-launched it from buildings for longer flights. Finally, he towed the lifting-body model aloft using a powered model airplane known as the "Mothership." A timer released the model and it glided to a landing. Dale's wife Donna used a 9 mm. camera to film the flights of the model. Its stability as it glided--despite its lack of wings--convinced Milt Thompson and some Flight Research Center engineers including the center director, Paul Bikle, that a piloted lifting body was possible. The lifting body concept evolved in the mid-1950s as researchers considered alternatives to ballistic reentries of piloted space capsules. The designs for hypersonic, wingless vehicles were on the boards at NASA Ames and NASA Langley facilities, while the US Air Force was gearing up for its Dyna-Soar program, which defined the need for a spacecraft that would land like an airplane. Despite favorable research on lifting bodies, there was little support for a flight program. Dryden engineer R. Dale Reed was intrigued with the lifting body concept, and reasoned that some sort of flight demonstration was needed before wingless aircraft could be taken seriously. In February 1962, he built a model lifting body based upon the Ames M2 design, and air-launched it from a radio controlled "mothership." Home movies of these flights, plus the support of research pilot Milt Thompson, helped pursuade the facilities director, Paul Bikle, to give the go-ahead for the construction of a full-scale version, to be used as a wind-tunnel model and possibly flown as a glider. Comparing lifting bodies to space capsules, an unofficial motto of the project was, "Don't be Rescued from Outer Space--Fly Back in Style." The construction of the M2-F1 was a joint effort by Dryden and a local glider manufacturer, the Briegleb Glider Company. The budget was $30,000. NASA craftsmen and engineers built the tubular steel interior frame. Its mahogany plywood shell was hand-made by Gus Briegleb and company. Ernie Lowder, a NASA craftsman who had worked on the Howard Hughes "Spruce Goose," was assigned to help Briegleb. The prototype of a 21st Century spacecraft required the fabrication of hundreds of small wooden parts meticulously nailed and glued together. It was a product of craftsmanship that was nearly obsolete in the 1940s. Final assembly of the remaining components (including aluminum tail surfaces, push rod controls, and landing gear from a Cessna 150) was done back at the NASA facility. In the meantime, other NASA engineers devised a special M2-F1 flight simulator, and a hot rod shop near Long Beach souped-up a Pontiac convertible to be used as the lifting body ground-tow vehicle. The M2-F1 did not have ailerons. Instead, it had elevons which were attached to each of the two rudders. A large flap on the trailing edge of the body acted as an elevator. This unconventional arrangement prompted the engineers to rethink the flight control system as well. They eventually devised two schemes. One system was fairly traditional. It used rudder pedal inputs to move the rudders for yaw control, and stick inputs to provide differential deflections of the elevons for roll. The other system used stick inputs to control the rudders for yaw, while rudder pedal deflections moved the elevons for roll. Milt Thompson tried both systems in the simulator and surprised the design team when he said he preferred system number two. He reasoned that although sideslip delayed roll (which was a result of dihedral effect), the roll rate was twice as high using the rudders instead of the elevons. He said he would rather have the higher roll rates available to him if needed, while the slip could be overcome with proper piloting technique. This was the system that Thompson practiced on the simulator, and he used it during the initial auto tows. Auto tows were done using a 1000 foot rope fastened to the NASA Pontiac. Rogers Dry Lake provided miles of unobstructed motoring. On April 5, 1963, Thompson lifted the M2-F1's nose off of the ground for the first time on tow. Speed was 86 miles per hour. The little craft seemed to bounce uncontrollably back and forth on the main landing gear, and stopped when he lowered the nose to the ground. He tried again, but each time with the same results. He felt it was a landing gear problem that could have caused the aircraft to roll on its back if he had lifting the main gear off of the ground. Looking at movies of the tests, engineers decided that the bouncing was probably caused by unwanted rudder movements. Flight control system number two was replaced in favor of number one, and it never bounced again. Speeds on tow inched up to 110 miles per hour, which allowed Thompson to climb to about 20 feet, then glide for about 20 seconds after releasing the line. That was the most that could be expected during an auto tow. In the spring of 1963 the M2-F1 was shipped to Ames Research Center, where it was mounted on twenty-foot poles inside the 40-foot by 80-foot wind tunnel. For two weeks, Thompson and engineers Ed Browne and Dick Eldredge took turns "flying" it as air blasted by at a 135 miles per hour. They learned more about its flying qualities, and accumulated important data for the upcoming aero tows. A NASA C-47 was used for all of the aero tows. The first was on August 16, 1963. The M2-F1 had recently been equipped with an ejection seat, small rockets in the tail to extend the landing flare for about 5 seconds (if needed), and Thompson prepared for the flight with a few more tows behind the Pontiac. Forward visibility in the M2-F1 was very limited on tow, requiring Thompson to fly about 20 feet higher than the C-47 so he could see the plane through the nose window. Towing speed was about 100 miles per hour. Tow release was at 12,000 feet. The lifting body descended at an average rate of about 3,600 feet-per-minute. At 1,000 feet above the ground, the nose was lowered to increase speed to about 150 mph, flare was at 200 feet from a 20 degree dive. The landing was smooth, and the lifting body program was on its way. The M2-F1 was flown until August 16, 1966. It proved the lifting body concept and lead the way for subsequent, metal "heavyweight" designs. Chuck Yeager, Bruce Peterson, Bill Dana, Jerry Gentry, James Wood, Don Sorlie, Fred Haise, Joe Engle, and Don Mallick also flew the M2-F1. More than 400 ground tows and 77 aircraft tow flights were carried out with the M2-F1. The success of Dryden's M2-F1 program led to NASA's development and construction of two heavyweight lifting bodies based on studies at NASA's Ames and Langley research centers--the M2-F2 and the HL-10, both built by the Northrop Corporation, and to the Air Force's X-24 program, for which the vehicles were built by Martin. The Lifting Body program also heavily influenced the Space Shuttle program. |
Date | |
Source | |
Author | NASA |
Other versions |
Dale Reed with Model in Front of M2-F1 - GPN-2000-000246.jpg: ![]() |
Posted InfoField | 10 October 2012, 18:14 |
DVIDS ID InfoField | 717045 |
![]() |
This image or video was catalogued by Armstrong Flight Research Center of the United States National Aeronautics and Space Administration (NASA) under Photo ID: E-16475. This tag does not indicate the copyright status of the attached work. A normal copyright tag is still required. See Commons:Licensing. Other languages:
العربية ∙ беларуская (тарашкевіца) ∙ български ∙ català ∙ čeština ∙ dansk ∙ Deutsch ∙ English ∙ español ∙ فارسی ∙ français ∙ galego ∙ magyar ∙ հայերեն ∙ Bahasa Indonesia ∙ italiano ∙ 日本語 ∙ македонски ∙ മലയാളം ∙ Nederlands ∙ polski ∙ português ∙ русский ∙ sicilianu ∙ slovenščina ∙ Türkçe ∙ українська ∙ 简体中文 ∙ 繁體中文 ∙ +/− |
Licensing
Public domainPublic domainfalsefalse |
![]() |
This file is in the public domain in the United States because it was solely created by NASA. NASA copyright policy states that "NASA material is not protected by copyright unless noted". (See Template:PD-USGov, NASA copyright policy page or JPL Image Use Policy.) | ![]() |
![]() |
Warnings:
|
Captions
Add a one-line explanation of what this file represents
Items portrayed in this file
depicts
image/jpeg
eb11fbb82eccc72b9160122b90175442a2a8546d
540,500 byte
3,000 pixel
2,400 pixel
File history
Click on a date/time to view the file as it appeared at that time.
Date/Time | Thumbnail | Dimensions | User | Comment | |
---|---|---|---|---|---|
current | 09:30, 19 October 2015 | ![]() | 2,400 × 3,000 (528 KB) | Revent | Higher resolution version of same image from NASA Armstrong Photo Gallery. |
20:39, 14 October 2015 | ![]() | 1,035 × 1,294 (161 KB) | Revent | Cropped 16 % vertically using CropTool with lossless mode. Removing caption. | |
08:56, 15 April 2015 | ![]() | 1,035 × 1,536 (201 KB) | Fæ | == {{int:filedesc}} == {{milim | description = {{en|1=Dale Reed with a model of the M2-F1 in front of the actual lifting body. Reed used the model to show the potential of the lifting bodies. He first flew it into tall grass to test stability and trim,... |
File usage
The following pages on the English Wikipedia use this file (pages on other projects are not listed):