Austin transformer

An Austin ring transformer is a special type of isolation transformer with low capacitance between the primary and secondary windings and high isolation.

Etymology[edit]

It is named after its inventor, Arthur O. Austin, who graduated from Stanford University in 1903 and who obtained 225 patents in his career.^[1]

Background[edit]

AM radio stations that broadcast in the medium frequency (MF) and low frequency (LF) bands typically use a type of antenna called a base-fed mast radiator. This is a tall radio mast in which the steel mast structure itself is energized and serves as the antenna. The mast is mounted on a ceramic insulator to isolate it from the ground and the feedline from the transmitter is bolted to it. Typically the mast will have a radio frequency AC potential of several thousand volts on it with respect to ground during operation.

Aviation regulations require that radio towers have aircraft warning lights along their length, so the tower will be visible to aircraft at night.^[2] The high voltage on the tower poses a problem with powering the lights. The power cable that runs down the tower and connects to the utility line is at the high voltage of the mast. Without protective equipment the RF current from the mast would flow down the cable to the power line ground, short-circuiting the mast. To prevent this, a protective isolator device is installed in the lighting power cable at the base of the mast which blocks the radio frequency power while allowing the 50/60 hertz AC mains power for the lights through.

Use and mechanism[edit]

The Austin transformer is a specialized type of isolation transformer made specifically for this use, in which the primary and secondary windings of the transformer are separated by an air gap, wide enough so the high voltage on the antenna cannot jump across.^[3]^[4] It consists of a ring-shaped toroidal iron core with the primary winding wrapped around it, mounted on a bracket from the mast's concrete base, connected to the lighting power source.^[5] The secondary winding which provides power to the mast lights is a ring-shaped coil which circles the toroidal core through the center, like two links in a chain, with an air gap between the two. The magnetic field created by the primary winding induces current in the secondary winding without the necessity of a direct connection between them. The wide gap of several centimeters between the coils also ensures that there is minimal interwinding capacitance, to prevent RF voltage being induced in the supply wiring by capacitive coupling. A spark gap is often located nearby with a gap smaller than the gap between the rings, to prevent damage to the transformer and transmitting equipment in the case of a lightning strike.

References[edit]

^ Austin insulators history, retrieved 2010 Nov 1
^ Laport, Edmund (1952). Radio Antenna Engineering. New York: McGraw-Hill Book Co. pp. 143–144. OCLC 758264513.
^ It is formed of two interlocking rings: one with the transformer core and primary windings, much like a conventional toroidal transformer and the other with the secondary windings. The secondary is wound like in a typical toroidal transformer but with a very large diameter to reduce interwinding capacitance and undesired capacitive coupling of RF energy. The power from primary to secondary is transferred by inductive coupling. It is used for providing power to the aircraft warning lights and other devices on a mast radiator antenna insulated from ground. In the Austin transformer the primary and secondary windings are separated by a large air gap, so that the high voltage and AM RF energy on the mast cannot couple into the low voltage lighting supply wiring, causing safety hazards and electromagnetic compatibility issues. Griffith, B. Whitfield (2000). "Practical operation of the vertical antenna". Radio-electronic transmission fundamentals (2nd ed.). Sci Tech Publishing. p. 367. ISBN 1-884932-13-4.
^ Mehla, Ishwar Singh (2018). AM Radio Tower Antennas. Chennai, India: Notion Press. Section 4.3.1(a). ISBN 978-1-64429-518-2.
^ Lockwood, Stephen S.; Cox, Bobby L. New tools to co-locate wireless devices with AM antennas (PDF) (Report). Kintronic Labs, Inc. Retrieved 7 April 2020.

External links[edit]

"Picture of an Austin transformer at a broadcast transmitter site". Retrieved 2020-04-12.

[1] Austin insulators history, retrieved 2010 Nov 1

[Laport1-2] Laport, Edmund (1952). Radio Antenna Engineering. New York: McGraw-Hill Book Co. pp. 143–144. OCLC 758264513.

[3] It is formed of two interlocking rings: one with the transformer core and primary windings, much like a conventional toroidal transformer and the other with the secondary windings. The secondary is wound like in a typical toroidal transformer but with a very large diameter to reduce interwinding capacitance and undesired capacitive coupling of RF energy. The power from primary to secondary is transferred by inductive coupling. It is used for providing power to the aircraft warning lights and other devices on a mast radiator antenna insulated from ground. In the Austin transformer the primary and secondary windings are separated by a large air gap, so that the high voltage and AM RF energy on the mast cannot couple into the low voltage lighting supply wiring, causing safety hazards and electromagnetic compatibility issues. Griffith, B. Whitfield (2000). "Practical operation of the vertical antenna". Radio-electronic transmission fundamentals (2nd ed.). Sci Tech Publishing. p. 367. ISBN 1-884932-13-4.

[4] Mehla, Ishwar Singh (2018). AM Radio Tower Antennas. Chennai, India: Notion Press. Section 4.3.1(a). ISBN 978-1-64429-518-2.

[Lockwood-5] Lockwood, Stephen S.; Cox, Bobby L. New tools to co-locate wireless devices with AM antennas (PDF) (Report). Kintronic Labs, Inc. Retrieved 7 April 2020.

[1]

[2]

[3]

[4]

[5]

v t e Transformer topics
Topics	Balun Buchholz relay Bushing Center tap Circle diagram Condition monitoring of transformers Electrical insulation paper Growler High-leg delta Induction regulator Leakage inductance Magnet wire Metadyne Open-circuit test Polarity Pressure relief valve Quadrature booster Resolver Resonant inductive coupling Severity factor Short-circuit test Stacking factor Synchro Tap changer Toroidal inductors and transformers Transformer oil Dissolved gas analysis Transformer oil testing Transformer utilization factor Vector group
Types	Autotransformer Buck–boost transformer Distribution transformer Pad-mounted transformer Delta-wye transformer Energy efficient transformer Amorphous metal transformer Flyback transformer Grounding transformer Instrument transformer Current transformer Voltage transformer Isolation transformer Austin transformer Linear variable differential transformer Parametric transformer Planar transformer Rotary transformer Rotary variable differential transformer Scott-T transformer Solid-state transformer Trigger transformer Variable-frequency transformer Zigzag transformer
Coils	Hybrid coil Induction coil Oudin coil Polyphase coil Repeating coil Tesla coil Trembler coil
Manufacturers	ABB General Electric Mitsubishi Electric ProlecGE Schneider Electric Siemens TBEA