Jump to content

Shearing (manufacturing)

From Wikipedia, the free encyclopedia
(Redirected from Guillotine shear)

Shearing, also known as die cutting,[1] is a process that cuts stock without the formation of chips or the use of burning or melting. Strictly speaking, if the cutting blades are straight the process is called shearing; if the cutting blades are curved then they are shearing-type operations.[2] The most commonly sheared materials are in the form of sheet metal or plates. However, rods can also be sheared. Shearing-type operations include blanking, piercing, roll slitting, and trimming. It is used for metal, fabric, paper and plastics.

Principle

[edit]

A punch (or moving blade) is used to push a workpiece against the die (or fixed blade), which is fixed. Usually, the clearance between the two is 5 to 40% of the thickness of the material, but dependent on the material. Clearance is defined as the separation between the blades, measured at the point where the cutting action takes place and perpendicular to the direction of blade movement. It affects the finish of the cut (burr) and the machine's power consumption. This causes the material to experience highly localized shear stresses between the punch and die. The material will then fail when the punch has moved 15 to 60% of the thickness of the material because the shear stresses are greater than the shear strength of the material and the remainder of the material is torn.

Two distinct sections can be seen on a sheared workpiece, the first part being plastic deformation and the second being fractured. Because of normal inhomogeneities in materials and inconsistencies in clearance between the punch and die, the shearing action does not occur in a uniform manner. The fracture will begin at the weakest point and progress to the next weakest point until the entire workpiece has been sheared; this is what causes the rough edge. The rough edge can be reduced if the workpiece is clamped from the top with a die cushion. Above a certain pressure, the fracture zone can be completely eliminated. However, the sheared edge of the workpiece will usually experience work-hardening and cracking. If the workpiece has too much clearance, then it may experience roll-over or heavy burring.

Tool materials

[edit]
  • Low alloy steel is used in low production of materials that range up to 0.64 cm (14 in) thick
  • High-carbon, high chromium steel is used in high production of materials that also range up to 0.64 cm (14 in) in thickness
  • Shock-resistant steel is used in materials that are equal to 0.64 cm (14 in) thick or more

Tolerances and surface finish

[edit]

When shearing a sheet, the typical tolerance is +0.1 inch or −0.1 inch, but it is feasible to get the tolerance to within +0.005 inch or −0.005 inch. While shearing a bar and angle, the typical tolerance is +0.06 inch or −0.06 inch, but it is possible to get the tolerance to +0.03 inch or −0.03 inches. Surface finishes typically occur within the 250 to 1000 microinches range but can range from 125 to 2000 microinches. A secondary operation is required if one wants better surfaces than this.

See also

[edit]

References

[edit]

Citations

[edit]
  1. ^ Wick & Veilleux 1984, p. 6‐20
  2. ^ Degarmo, p. 424.

General sources

[edit]
  • Degarmo, E. Paul; Black, J. T.; Kohser, Ronald A. (2003), Materials and Processes in Manufacturing (9th ed.), Wiley, ISBN 0-471-65653-4.
  • Todd, Robert H.; Allen, Dell K.; Alting, Leo (1994), Manufacturing Processes Reference Guide, Industrial Press Inc., ISBN 0-8311-3049-0.
  • Wick, Charles; Veilleux, Raymond F. (1984), Tool and Manufacturing Engineers Handbook: Forming (4th ed.), SME, ISBN 978-0-87263-135-9.
[edit]