Jump to content

Talk:Jet fuel

Page contents not supported in other languages.
From Wikipedia, the free encyclopedia

Steel beams

[edit]

Does anyone have information on this? I heard that steel beams can't be melted by jet fuel, and I'm highly curious now. -- Kjkolb 03:09, 18 December 2005 (UTC) — Preceding unsigned comment added by 86.131.37.100 (talk) [reply]


Combustion isn't really that simple, there's no exact temperature something burns at, it's a mix of a pretty long list of variables. Jet fuel, in the presence of enough oxygen, will burn at well over 3000c, which is more than hot enough to turn steel into liquid. In an open fuel fire, however, the flame will be starved for oxygen, and will not burn anywhere near as hot. What complicates things even further is if the steel beams in question are under load at the time. As noted above, steel gets soft long before it melts. If they get soft while under load, they will bend a significant amount, which will cause an enormous amount of internal friction, producing heat, and can then fully melt the steel.

As an interesting side note, acetylene, in an open fuel fire, will not burn anywhere near hot enough to melt steel, not even hot enough to make it glow. With enough oxygen, it burns at 3000c+, just like jet fuel. Acetylene is regularly used to not just melt, but actually vaporize a line of steel, thereby cutting it.

Whether or not something can melt steel beams depends much more on the available oxygen than it does on the fuel being used. Jet fuel absolutely can melt steel beams.

Untitled

[edit]

Just a note on sourcing, material for this page was originally taken from the article on aviation fuel. -Lommer | talk 17:30, 28 August 2005 (UTC)[reply]

Kerosene and naphtha-type jet fuels

[edit]

Does anyone have information on these? I'm getting conflicting definitions. -- Kjkolb 03:09, 18 December 2005 (UTC)[reply]

Did you read the article? It's called Jet B and is discussed at some length. Or is there something specific ygfhdgfdhfhfhfghdfghgfhfghfdhou'd like to know that isn't covered there? -User:Lommer | talk 23:46, 18 December 2005 (UTC)[reply]
I'm sorry, I guess I didn't make myself clear. Kerosene and naphtha type fuels appear to refer to two different types of fuels, so if that is the case, it wouldn't be just Jet B. I've found various definitions for each type. -- Kjkolb 01:50, 19 December 2005 (UTC)[reply]
Hrm. I'm not sure. Jet A is basically pure kerosene, Jet B is a naptha-kerosene blend, so I guess it's entirely possible that there are even lighter pure-naptha jet fuels out there. After all, it's possible to burn almost anything in a jet engine, even avgas works just fine (I've seen it done). In fact there was one company I know of that put a tank of avgas through its garrett-powered king air once every year for "cleaning purposes". When I asked other AMEs about this they said they didn't see the need but that it wouldn't hurt the engine... -User:Lommer | talk 05:49, 19 December 2005 (UTC)[reply]
Maybe the terms aren't used in the aviation industry, just in refining or energy statistics. These are the definitions from the Department of Energy.
This entry should be completely rewritten. As said above, a jet engine can take most, the composition of the fuel is trivial, the main blend, "Jet Fuel 1A, Colonial Blend 54" is not even mentioned, while 9/11 and melting point of stell, the collapse of the Twin Tower is shed light on by even more hearsay. The section should be linked to jet engines and turbo-props / helicopter engines. Please ask me if you are ready for a complete revision of the entry. --KH Flottorp 22:31, 27 March 2007 (UTC)[reply]
Kerosene-type - A kerosene-based product having a maximum distillation temperature of 205 degrees Celsius at the 10-percent recovery point and a final maximum boiling point of 300 degrees Celsius and meeting ASTM Specification D 1655 and Military Specifications MIL-T-5624P and MIL-T-8133D (Grades JP-5 and JP-8). It is used for commercial and military turbojet and turboprop aircraft engines.
Naphtha-type - A fuel in the heavy naphtha boiling range having an average gravity of 52.8 degrees API, 20 to 90 percent distillation temperatures of 145 degrees to 245 degrees Celsius, and meeting Military Specification MIL-T-5624L (Grade JP-4). It is used primarily for military turbojet and turboprop aircraft engines because it has a lower freeze point than other aviation fuels and meets engine requirements at high altitudes and speeds.
Does this seem right to you? As I said, I've found conflicting definitions. -- Kjkolb 08:19, 19 December 2005 (UTC)[reply]
Oh that makes sense; JP-4 is Jet B, and JP-8 is Jet A, (JP-5 is between the two IIRC). So yeah, Kerosene-type is Jet A and similar fuels while Naptha-type refers to Jet B. -User:Lommer | talk 02:29, 21 December 2005 (UTC)[reply]

Okay. I put a little information about them in the article. Modify or delete, if necessary. -- Kjkolb 05:50, 21 December 2005 (UTC)[reply]

Any experts on jet fuel's flashpoint?

[edit]

Hi. Sort of off-topic for Wikipedia in a sense. But this could help another article on wikipedia. A series of US "Experts" claim that 9/11 could be a hoax based on a set of reasons they've outline. One of them is that:

  • "Since the melting point of iron is 1537*C or 2,798.6*F, the temperature of jet fuel fires does not exceed 1,800*F under optimal conditions, and UL certified the steel used to 2,000*F for six hours, the buildings cannot have collapsed due to heat from the fires. How is this possible?

Does anyone happen to know if these temperatures quoted could be correct?

I contend anyone can throw a bunch of facts and figures against a chalk board and contend it is so. And a majority of the people who have *no idea* of what is true or not, might 'buy it' and accept it as fact. So my question is do these temperatures in fact hold true based on the knowledge of others here?

Talk:September_11,_2001_attacks#Experts_Claim_Official_9.2F11_Story_is_a_Hoax.3F

Source: Experts Claim Official 9/11 Story is a Hoax

--CaribDigita

Regarding jet fuel burn temperature: There is no single temperature at which fuel burns. It depends on the available oxygen. According to this flame temperature in the core of a jet engine is approximately 2,000F. More enough to melt steel. — Preceding unsigned comment added by 2600:1700:87D0:5490:65F2:AC45:1514:7FB1 (talk) 17:56, 27 March 2019 (UTC)[reply]

Steel does not have to melt to be weakened, causing a collapse. -- Kjkolb 21:01, 11 February 2006 (UTC)[reply]

I took a look at the article. There are solid answers to all of the questions. It says that experts came up with these questions, but most show scientific ignorance and/or illogic. Besides the steel being weakened by heat, another example is, "the buildings were designed with load redistribution capabilities to withstand the impact of airliners, whose effects would be like "puncturing mosquito netting with a pencil." Yet they completely collapsed. How is this possible?" If the planes had simply crashed into the buildings, they would have stayed up. However, fires burned for hours inside them, which weakened the steel and caused them to collapse. -- Kjkolb 21:13, 11 February 2006 (UTC)[reply]

"The official report, for example, entirely ignores the collapse of WTC7, a 47-story building, which was hit by no airplanes, was only damaged by a few small fires, and fell seven hours after the attack." The building was allowed to burn because it was empty. It collapse because it was weakened, just like the others.

"A former Inspector General for the Air Force has observed that Flight 93, which allegedly crashed in Pennsylvania, should have left debris scattered over an area less than the size of a city block; but it is scattered over an area of about eight square miles." I cannot think of a reason for the debris to be limited to a city block. I have searched for other crashes and eight square miles is a reasonable figure. Also, accident investigation does not appear to be a part of the Inspector General's job, "The primary charge of the IG is to sustain a credible Air Force IG system by ensuring the existence of responsive complaint investigations, and FWA programs characterized by objectivity, integrity, and impartiality. Only the IG may investigate allegations of reprisal under the Military Whistleblower’s Protection Act."

"The Pentagon conducted a training exercise called "MASCAL" simulating the crash of a Boeing 757 into the building on 24 October 2000, and yet Condoleezza Rice, among others, has repeatedly asserted that "no one ever imagined" a domestic airplane could be used as a weapon. How is this possible?" There are several answers to this. The first is that she was lying because she did not want to look bad because if she knew, she, or the administration, should have done something to prevent it. Another is that she was not aware of such a simulation. She was a military advisor, but that does not mean she knows about all of the training exercises that they do. The last reason I can think of right now is that she may have known about the simulation, but considered it so unlikely that she did not consider it a threat.

"Foreign "terrorists" who were clever enough to coordinate hijacking four commercial airliners seemingly did not know that the least damage to the Pentagon would be done by hitting its west wing. How is this possible?" They had some intelligence, but they were far from brilliant. Also, smart people can make mistakes. Also, they may not have had very good control over the descent. Finally, there is a good chance that they did not know the wing was being renovated.

"The BBC has reported that at least five of the nineteen alleged "hijackers" have turned up alive and well living in Saudi Arabia, yet according to the FBI, they were among those killed in the attacks. How is this possible?" The most likely reasons are that they were wrong about who some of the hijackers were or the people found in Saudi Arabia were misidentified.

"Their own physics research has established that only controlled demolitions are consistent with the near-gravity speed of fall and virtually symmetrical collapse of all three of the WTC buildings. While turning concrete into very fine dust, they fell straight-down into their own footprints." There is no reason given why the collapse should not have been similar to a demolition. It was somewhat similar. Implosions usually take out the first floor or two, but with so many floors above the crash sites, it did not matter. -- Kjkolb 21:57, 11 February 2006 (UTC)[reply]

Okay, I understand where you are coming from here with regard to the official story of 9-11 and the science of jet fuel. However, I feel it my need to correct you on the fact that although jet fuel burns at 1800 degrees under optimal conditions, the state of optimal conditions for the burning of jet fuel is within a jet engine under 10-20 atmospheres of pressue. When the fuel leaves the engine, it cools down to within 450-500 degrees in seconds, jet fuel just can't hold all that heat in thin air! Steel reaches red heat(the tempurature at which its structure is compromised) at 600 degrees, this means that the steel in those buildings was not even weakened by the fuel as you contend. With regard to the Saudis who are still alive, you are probably familiar with the amount of personal information one has to hand over to get a plane ticket; therefore it is highly unprobable that in their investigation the FBI simply "got things wrong" they most likely lied instead.I'm not telling you what happened because I honestly don't know, I'm just telling you what didn't happen. For any further questions, feel free to email.

It's best not to post your email address here, so I removed it. If anyone wants to reply, they can do so here. Although this is off topic, I don't think it is a big deal in this situation and it can be deleted later. Anyway, the jet fuel was not burning in a jet engine or at high altitude, so the temperature would be higher.
As for the passengers, they may have been using fake information, as you suggested. I would not be surprised if they did. However, the BBC seems to be using only names for identifying the passengers (at least some of them), which is very inaccurate when you're dealing with such a large population. In fact, they have found more than one person with the name Abdulaziz Al Omari. The BBC saying that they have definitely found the suspects alive based upon such information is unethical. -- Kjkolb 02:30, 25 March 2006 (UTC)[reply]

Maximum adiabatic combustion temperatures of kerosene/jet-A1 fuel is 2300° Kelvin or 2027° Celsius (3680° Fahrenheit), which is hot enough to melt steel. 24.200.17.245 (talk) 09:43, 18 December 2007 (UTC)[reply]


911 is a lie, investigate for youself, get ready for martail law and fema death camps —Preceding unsigned comment added by 76.87.43.34 (talk) 15:09, 25 August 2008 (UTC)[reply]

The moon landings were fake too - they should have brought back green cheese, but instead only brought back rocks which proves it. — Preceding unsigned comment added by 192.158.48.162 (talk) 13:52, 5 August 2016 (UTC)[reply]


Average rebar (construction, reinforces concrete) may melt at 1500C but it undergoes internal changes that soften it ~800C. The Empire State building has been hit by aircraft several times but it has a strong core structure and used large steel beams. The World Trade Center buildings, like most new construction, is based on thick Steel (often thick walled Steel tubes filled with concrete) struts along the periphery of the building footprint with thinner steel beams actually supporting individual floors (each floor is mostly empty so strength needed was minimal). The weld joints of the thin steel floor beams to thick steel support structure is tricky and even a good welder can leave behind a weak joint. In 1980's, a building of this type, under construction (up to the 50th floor), had a failure near the top floors and as that floor pancaked into the floor below the combined weight was too much for lower floors so they pancaked also (a dozen or so construction workers died). Hence only enough heat to partially weaken (not melt) an upper floor's (already weak) attachment to the to the peripheral support structure was needed. Don't forget that a 747 weighs a ~400 tons, as well. The use of a fully fueled jet to attack a building was broached in Tom Clancy's "Debt of Honor" in 1994. (Apparently Osama was an avid reader.) Fully fueled has 400,000 pounds of fuel which has more energy than an equivalent weight of TNT. Hiroshima was hit by a 5 kiloton (10,000 pounds TNT equivalent)bomb. The collapse itself converted potential energy into more than a few kilotons of TNT. Shjacks45 (talk) 04:27, 7 September 2018 (UTC)[reply]

No Lead in Jet Fuel

[edit]

"Lead is not added to diesel fuel or jet fuel" http://www.environment.nsw.gov.au/leadsafe/leadinf6.htm

"JP fuels do not contain tetraethyl lead." http://www.pilotfriend.com/aeromed/medical/toxic.htm

"Turbine fuels are high-quality fuels covering the general heavy gasoline and kerosene boding range. They do not contain dyes or tetraethyl lead." http://www.cavalrypilot.com/fm1-506/ch1.htm

"Jet A in the United States usually contains no additives at all, or perhaps only an antioxidant." and "The approved antioxidants for aviation fuel are hindered phenols." http://www.chevron.com/products/prodserv/fuels/bulletin/aviationfuel/4_at_fuel_comp.shtm#basefuel

Inaccuracies in the Jet Fuel article

[edit]

I would recommend that this article be re-written. The first sentence, stating that jet fuel is gray, is completely inaccurate. Jet fuel is clear to straw colored, as it states later in the article, and any jet fuel that was gray would be severely contaminated. In addition, most of the article is uncited, and the only source cited doesn't contain most of the information that is portrayed in the article. The history of jet fuel section doesn't actually talk about the history at all, but rather discusses the composition of jet fuel. It's a good start for the article, it just needs some revision.

Also it states "Jet A is the standard jet fuel type in the U.S. since the 1950s and is only available there". So what do the rest of the world use? —Preceding unsigned comment added by 80.79.80.249 (talk) 15:02, 28 September 2007 (UTC)[reply]

Actually most jet fuel exported from Russia etc. is "JP54" or "Colonial JP54". It is similar to "Jet A" except the the Specific Energy is 18.4 mj/kg compared to that of 42.8 mj/kg of "Jet A". Also there is a slight difference in additives. —Preceding unsigned comment added by 71.158.220.38 (talk) 00:06, 11 August 2008 (UTC)[reply]
If I have read the article correctly, Jet A is used in the USA and Jet A-1 is used everywhere else, except in cold countries where Jet B is used. Is this right? The article is not at all clear. Biscuittin (talk) 15:49, 2 March 2009 (UTC)[reply]

Commercial aircraft around most of the world use Jet A-1, usually requiring the fuel to meet the specifications of the Joint Fuelling System Checklift for Jet A-1. Jet B is a wide cut kerosene, meaning that it has a higher proportion of lighter hydrocarbons (shorter carbon chains). This lowers the freezing point of the fuel (Jet A-1 freezes at -47degC) allowing the aircraft the fly to much colder environments (think antarctica). — Preceding unsigned comment added by 2.217.206.175 (talk) 20:06, 7 July 2011 (UTC)[reply]

Chemical composition of jet fuel

[edit]

On 10 October, Cypoet added a "Chemical compound" attribute to the list of properties of Jet A-1 at the top of the article. Unfortunately, this addition incorrectly suggests that jet fuel is a single chemical compound, dodecane. Jet fuel is actually a complex blend of hundreds of hydrocarbons. I've taken the "Chemical compound" attribute out of the table and added a paragraph to the "Description" section of the article with a more detailed and accurate description of the actual composition, including a citation. Piperh 10:50, 4 November 2007 (UTC)[reply]

Does "Aeroplane" mean "Jet"?

[edit]

The lead paragraph speaks repeatedly of "Aeroplane fuel" while talking about jet fuel. Is "Aeroplane" a British synonym for "Jet"? Or should the relevent sections be changed to the more explicit "Jet aeroplane"? —Preceding unsigned comment added by Loren.wilton (talkcontribs) 09:34, 25 January 2008 (UTC)[reply]

In the UK we use Aeroplane instead of Airplane, it does not specifically refer to any type of aircraft. Comrinec (talk) 21:17, 6 July 2008 (UTC)[reply]

Also, keep in mind that jet fuel is also burned by turboprop and turboshaft engines. Neither are "jets", and turboshaft engines are used in helicopters, not airplanes. This is why in technical discussion we use the more accurate term "gas turbine fuel" to describe jet fuel, even though this is not the common term. Shreditor (talk) 22:25, 6 July 2008 (UTC)[reply]
Also, there are diesel based light aircraft that burn 'jet fuel' also. — Preceding unsigned comment added by James shoemaker (talkcontribs) 23:37, 8 November 2020 (UTC)[reply]

JP-10

[edit]

Was surprised to not find a page on JP-10, which I was just looking for. DonPMitchell (talk) 21:29, 15 July 2008 (UTC)[reply]

This link is still pointing to https://en.wikipedia.org/wiki/JP-10 which is about Gunma Prefecture in Japan. Can't find an article about JP-10 at all. NutterguyIrl 18:13, 02 Febuary 2014 (UTC)

...the technology is still in it's infancy...?

[edit]

I was surprised to find this claim, as diesel engines have been around for more than 100 years, and turbocharged diesel engines have been around for as long as turbocharged gasoline engines. Furthermore, a diesel engine is less complex than a gasoline engine. One does not have to worry about having a dual ignition system, as diesels don't use spark plugs. The glow plugs (igniters) used are simple resistive elements which don't require RF shielding as do the gasoline engines' twin magneto system.

In short, the technology has been around for many decades. It is not "in it's infancy." —Preceding unsigned comment added by 132.25.0.207 (talk) 11:11, 25 July 2008 (UTC)[reply]

I wrote that statement, so I'll take a stab at explaining it... Yes, diesel engines have been around for a long time, but very very few have found use in aircraft. As of 2008 Thielert is the only company I know of building certified aircraft diesel engines, and they're currently insolvent because of numerous customer support problems. So yes, I would call that a technology in its infancy, since it hasn't been developed to the point of becoming a significant part of the aerospace economy. I don't mean to be overly negative, here. I personally think aircraft diesel engines have great potential. They just haven't reached it... yet. Shreditor (talk) 20:58, 25 July 2008 (UTC)[reply]
The German Junkers company produced a number of inline diesels for aircraft use in the 1930s, although they were heavier than the equivalent petrol engine and therefore had much poorer power-to-weight ratio, which is an important disadvantage in an aero engine. They were used mainly on flying boats such as the Bv 138 that needed the longer range possible with a diesel. — Preceding unsigned comment added by 80.4.57.101 (talk) 11:56, 7 October 2011 (UTC)[reply]

Maximum Burning Temperature

[edit]

There is no such thing as a maximum burning temperature. The phrase only exists on 9/11 conspiracy pages, this wikipedia page, and some Yahoo Answers pages which source from these two things. The concept of a "maximum burning temperature" does not exist within chemistry or thermodynamics, and does not have a scientific origin. In reality, combustion is a chemical process which generates energy. Generating energy raises the temperature. This process does not have a "maximum" like stated here. Please do not add the phrase back to this article. Jojobe (talk) 16:44, 31 July 2008 (UTC)[reply]

"In reality, combustion is a chemical process which generates energy." Oh, great that you finally made us aware of this important fact! Yes, of course adding heat in a closed space would cause its temperature to rise and rise, but in real life, including inside jet engines, these kind of fuels have a limit before pressure and other processes forces the temperature down. And as stated here, burning jet fuel in open air does not have a tremendously high temperature, far away from even weakening construction steel enough to bend it.
Also even if you may claim that the initial heat of the jet flame was higher than in free air, it would certainly not be higher once burning inside the 9/11 complex. Sometimes politics and patriotic "responsibility" can seem go far past what we would normally call 'scientific reason'. I know I'm not the only one thinking that.... --Nabo0o (talk) 23:04, 19 July 2009 (UTC)[reply]
Probably is wrong term there. This temperature seems as value of Fire point. --Postrach (talk) 12:05, 27 October 2009 (UTC)[reply]

The entire article is dodgy. The free-air burn temperature is pulled out of somebody's rear end. Jet-A1 can (and does) burn in free-air at an average of about 2000 C. This is why airports and military air installations have such strict handling protocols (and its also corrosive), and yes, this is why the cores of the NYC USA WTC towers melted. I've given up on Wikipedia as a source of anything accurate, I just use it as a jumping-off point these days to try and find the actual facts. Some urls, if anyone can be bothered then by all means add them to the external references:

Firefighting, quotes "3,000 - 4,000 F" (search on '3,000'):

http://aviationsafetyadvisorygroup.org/projects-initiatives/resource-guide-to-aircraft-fire-fighting-rescue/

SAE informative (search on '2263K'):

http://papers.sae.org/2012-01-1199/

Chart of various physicalities including adiabatic (approximation to 'free-air') burn temperature (search on 'Kerosene Jet A-1'), source - Isidoro Martínez, Prof. of Thermodynamics, ETSIA-UPM, Ciudad Universitaria, E-28040-Madrid:

http://webserver.dmt.upm.es/~isidoro/dat1/eCombus.pdf

124.168.113.23 (talk) 05:58, 28 April 2014 (UTC)[reply]

Density

[edit]

Suggest adding that the density of JET A is 6.3 to 7.1 pounds per US gallon with a standard of 6.7 pounds per US gallon —Preceding unsigned comment added by 70.43.169.213 (talk) 18:29, 5 September 2008 (UTC) pra mim jetfuel é um homem que vê o 1749 a circular com um volante dum O530 na 203...isso sim é um verdadeiro jetfuel...hum... jetfuel pode ser tambem considerado uma betoneira....pronto ok um burro.exta foi de homem.... —Preceding unsigned comment added by 213.63.59.42 (talk) 18:25, 5 March 2009 (UTC)[reply]

Lacking actual detail

[edit]

Enough of this lamer common knowledge such as "it is a mixture of this and that". How is Jet-A fuel manufactured? Provide with hand book description of do-it-yourself Teemu Ruskeepää (talk) 08:33, 15 March 2009 (UTC)[reply]

No, I don't agree that this article should include a recipe for DIY-ers. Binksternet (talk) 16:13, 15 March 2009 (UTC)[reply]

Aviation fuels are often what is called "straight run fuels," meaning that as the crude oil is heated and evaporates in a distillation column, different fuels are drawn off at different hieghts depending on their density. (Have a look at oil refinery processes.) Kerosene is drawn off below gasoline but above diesel. It is called a straight run fuel because after being drawn off the distillation column, it does not usually require any other processing prior to use, except for the blending in of additives if required. — Preceding unsigned comment added by 2.217.206.175 (talk) 19:57, 7 July 2011 (UTC)[reply]

oposed to that (citation:"Aviation fuels are often what is called 'straight run fuels,'.."), I learned from Shell that 100LL (another aviation fuel) is basicaly made from synthetic hydro-carbon molecules. That is exactly the extreme opposite from "straight run fuel". How do you explain that?

--Cosy-ch (talk) 13:08, 13 July 2015 (UTC)[reply]

100LL is a petrol (avgas), not a jet fuel. you could put it in your car. — Preceding unsigned comment added by Mycosys (talkcontribs) 21:18, 29 August 2015 (UTC)[reply]

Lacking verification and factual accuracy

[edit]

This article is lacking any verification and some of it is just factually incorrect. I will attempt to clean it up over the next few days. Also bits of it need rephrasing to make it clearer Veryangrypenguin (talk) 12:57, 10 February 2010 (UTC)[reply]

COI Contributions

[edit]

I have a financial COI with Honeywell in that they’ve recruited me to help them navigate through Wikipedia and COI Best Practices. I'd like to offer the following contributions. User:King4057 (EthicalWiki) 16:22, 13 August 2012 (UTC)[reply]

Military Jet Fuels

[edit]

A paragraph at the end of the Military Jet Fuels section

The US Air Force C-17 Globemaster III was built to perform development testing.
The US Air Force’s C-17 Globemaster III, F-16 and F-15 are certified for use of hydrotreated renewable jet fuels.[1][2] The US Air Force plans to certify over 40 models for fuels derived from waste oils and plants by 2013.[2] The army is considered one of the few customers of biofuels large enough to potentially bring biofuels up to the volume production needed to reduce costs.[2] The US Air Force has also flown a Green Hornet fighter at 1.7 times the speed of sound using a biofuel blend.[2] The Defense Advanced Research Projects Agency (DARPA) funded a $6.7 million project with Honeywell UOP to develop technologies to create jet fuels from biofeedstocks for use by the US and NATO militaries.[3]

Jet Biofuels

[edit]

For the end of the Jet Biofuels bullets

  • 24 commercial and military biofuel flights have taken place using Honeywell “Green Jet Fuel,” including a Navy F/A-18 Hornet.[4]

References

[edit]
  1. ^ Dowdell, Richelle (February 10, 2011). "Officials certify first aircraft for biofuel usage". The Official Website of the US Air Force. Retrieved March 7, 2012. {{cite news}}: Cite has empty unknown parameter: |coauthors= (help)
  2. ^ a b c d Morales, Alex (October 18, 2011). "Fat Replaces Oil for F-16s as Biofuels Head to War: Commodities". BusinessWeek. Retrieved March 7, 2012. {{cite news}}: Unknown parameter |coauthors= ignored (|author= suggested) (help)
  3. ^ "UOP To Develop Technology to Produce Bio JP-8 for Military Jets". Green Car Congress. June 28, 2007. Retrieved March 7, 2012.
  4. ^ Koch, Wendy (November 7, 2011). "United flies first U.S. passengers using fuel from algae". USA Today. Retrieved December 16, 2011.

Feedback from other editors

[edit]

Text is well sourced and a good improvement to the article.

Water in jet fuel

[edit]

It should also be mentioned that water may be desirable in the jet engine in addition to hydrocarbon fuels, as a means of performance enhancement (usually in a mixture of water-alcohol, aka MW-50 injector).

Given a little extra vodka, a Mi-26 helo, officially certifed for 20 tons will lift a 27-ton frozen mammoth, as seen on National Geographic (behold the main rotor cone angle).

The problem arises when water gets mixed with hydrocarbons already in the fuel tank, however. 82.131.129.178 (talk) 18:01, 24 February 2013 (UTC)[reply]

That info belongs on the jet engine page, not here. The water is not mixed with the fuel, it is injected as the fuel burns, to lower the turbine-entry temperature. It also increases the mass-flow of the engine, and adds thrust by boiling into steam, which occupies far more volume than water does. None of this is relevant to jet fuel per se, only to the operation of turbine engines..45Colt 06:44, 12 September 2014 (UTC)[reply]

Soviet fuel classification

[edit]

It is crucial for the article to include comparison with the Soviet fuel classification (TS-1, RT and the stuff). Soviet-designed aircraft dominate the world market and post-Soviet air forces constitute the majority of world military jets - all using Soviet fuel classification. — Preceding unsigned comment added by 95.133.131.171 (talk) 14:51, 13 March 2013 (UTC)[reply]

so add it http://www.exxonmobil.com/AviationGlobal/Files/WorldJetFuelSpecifications2005.pdf contains a decent amount of info on international fuels and standards including types and availability in the CIS if you wish to add them Mycosys (talk) 21:20, 29 August 2015 (UTC)[reply]

Merger proposal

[edit]

I am proposing that all the jet fuel articles be placed under one roof as it is unnecessary to have individual articles.--Petebutt (talk) 18:34, 7 December 2013 (UTC)[reply]

  • Oppose Lots of things can be considered both "unnecessary", yet also "justified". Which makes the better articles? There are not a great many specific jet fuels (and there are excellent sources available). We can construct an article for each, with an overall article too, and this gives the best presentation of content to our readers. Andy Dingley (talk) 19:42, 7 December 2013 (UTC)[reply]
  • Oppose I would argue that there is a level of detail on the individual articles which does not fit in the overarching article. The JP-7 article, for example, lists the chemical characteristics of the fuel Bobbyd2500 (talk) 01:50, 2 January 2014 (UTC)[reply]

vs. automobile fuel

[edit]

Mention how jet fuel differs from automobile fuel. Jidanni (talk) 00:02, 14 December 2013 (UTC)[reply]

it already states it is a kerosene Mycosys (talk) 21:22, 29 August 2015 (UTC)[reply]

Flash Point Incorrect?

[edit]

Been researching the Flashpoint of Aviation (Jet) Fuel...

Obviously depending on the make up, the actual flash point can alter however:

Flash point says >60°C Jet fuel says 38°C

According to the article, they are the same thing — Preceding unsigned comment added by Willbo987 (talkcontribs) 15:01, 14 January 2014 (UTC)[reply]

JP-4 naming?

[edit]

JP-4 was a fuel developed for carrier use, during the transitional phase from piston engines. A low fire risk kerosene fuel was stored, with other tanks still carrying large stock of AVGAS gasoline. For fuelling jet aircraft, the two would first be mixed.

Was JP-4 the designation for the stored kerosene, or for the mixed blend? In such a case, what was the other (blended / stored) component called? Andy Dingley (talk) 16:32, 9 April 2014 (UTC)[reply]

No information on production

[edit]

There is no information in this article about the production of jet fuel witch I believe should be added. XStellarx (talk) 15:31, 13 June 2014 (UTC)[reply]

Lubricity confusion

[edit]

I added a {confusing} tag to the section on ground use. The second paragraph claims airport support vehicles running on Jet-A suffer from increased wear and tear due to the decreased lubricity of Jet-A fuel compared to diesel. The following paragraph states the exact opposite: That Jet-A, due to its higher sulfur content, has BETTER lubricity. These claims are mutually exclusive, and I do not know which one is correct. Stian (talk) 07:37, 25 July 2014 (UTC)[reply]

That's exactly what I came for. It says:

"Jet fuel is often used in ground support vehicles at airports, instead of diesel. The United States military makes heavy use of JP-8, for instance. However, jet fuel tends to have poor lubricating ability in comparison to diesel, thereby increasing wear on fuel pumps and other related engine parts. Civilian vehicles tend to disallow its use, or require that an additive be mixed with the jet fuel to restore its lubricity. Jet fuel is more expensive than diesel fuel but the logistical advantages of using one fuel can offset the extra expense of its use in certain circumstances.

Jet fuel contains more sulfur, up to 1,000 ppm, which therefore it is more lubricative and does not currently require a lubricity additive as all pipeline diesel fuels require. The introduction of Ultra Low Sulfur Diesel or ULSD brought with it the need for lubricity modifiers. Pipeline diesels before ULSD were able to contain up to 500 ppm of sulfur and was called Low Sulfur Diesel or LSD. LSD is not only available to the off-road construction, locative and marine markets. As more EPA regulations are introduced, more refineries are hydrotreating their jet fuel production, thus limiting the lubricating abilities of jet fuel, as determined by ASTM Standard D445."

Clearly this is conflicting. They can't both be accurate..45Colt 06:51, 12 September 2014 (UTC)[reply]

Still no consensus on the correct answer? Its been two years. — Preceding unsigned comment added by 151.165.212.93 (talk) 18:32, 20 July 2016 (UTC)[reply]

Flash point

[edit]

Flash point is definitely lower than 60°C. According to every single MSDS I've found, it's 38°C or 100°F. I am not an expert on Jet fuel, but I do work in the oil storage industry and know that in Europe Jet fuel is a class 2 product, meaning its flash point is between 21°C and 55°C. So 60 is most definitely too high. — Preceding unsigned comment added by 195.18.82.195 (talk) 06:57, 29 July 2014 (UTC)[reply]

If you're in the industry, does that give you access to good sources? That would clear it up nicely. Andy Dingley (talk) 11:33, 19 November 2014 (UTC)[reply]
Per the article tags, there also seems to be some confusion between flashpoint and autoignition temperatures. Andy Dingley (talk) 11:34, 19 November 2014 (UTC)[reply]

Reference not accessible

[edit]

When clicking this reference: "Beginner's Guide to Aviation Biofuels". Air Transport Action Group. May 2009. Retrieved 2009-09-20.

I am asked to log in, and I am not able to access it. Is there another way to get this file? It seems unwise for Wikipedia to use sources that are inaccessible to most people. 174.52.198.8 (talk) 02:56, 31 January 2015 (UTC)[reply]

NFPA versus GHS

[edit]

Is Wikipedia english international ? Yes? I say no. Because of a local, in international business no more valid hazardous indication system called NFPA. The GHS instead was created (1992) and implemented (2000) by the United Nations for worldwide use, and YES, mandatory for each chem travelling.

Why you are sticking the head in the sand and even not mention the GHS indication for JET A? --Cosy-ch (talk) 13:02, 13 July 2015 (UTC) so globalize or add {globalize} Mycosys (talk) 22:58, 29 August 2015 (UTC)[reply]

[edit]

Hello fellow Wikipedians,

I have just added archive links to one external link on Jet fuel. Please take a moment to review my edit. If necessary, add {{cbignore}} after the link to keep me from modifying it. Alternatively, you can add {{nobots|deny=InternetArchiveBot}} to keep me off the page altogether. I made the following changes:

When you have finished reviewing my changes, please set the checked parameter below to true to let others know.

This message was posted before February 2018. After February 2018, "External links modified" talk page sections are no longer generated or monitored by InternetArchiveBot. No special action is required regarding these talk page notices, other than regular verification using the archive tool instructions below. Editors have permission to delete these "External links modified" talk page sections if they want to de-clutter talk pages, but see the RfC before doing mass systematic removals. This message is updated dynamically through the template {{source check}} (last update: 5 June 2024).

  • If you have discovered URLs which were erroneously considered dead by the bot, you can report them with this tool.
  • If you found an error with any archives or the URLs themselves, you can fix them with this tool.

Cheers.—cyberbot IITalk to my owner:Online 15:01, 9 January 2016 (UTC)[reply]

[edit]

Hello fellow Wikipedians,

I have just added archive links to one external link on Jet fuel. Please take a moment to review my edit. If necessary, add {{cbignore}} after the link to keep me from modifying it. Alternatively, you can add {{nobots|deny=InternetArchiveBot}} to keep me off the page altogether. I made the following changes:

When you have finished reviewing my changes, please set the checked parameter below to true or failed to let others know (documentation at {{Sourcecheck}}).

This message was posted before February 2018. After February 2018, "External links modified" talk page sections are no longer generated or monitored by InternetArchiveBot. No special action is required regarding these talk page notices, other than regular verification using the archive tool instructions below. Editors have permission to delete these "External links modified" talk page sections if they want to de-clutter talk pages, but see the RfC before doing mass systematic removals. This message is updated dynamically through the template {{source check}} (last update: 5 June 2024).

  • If you have discovered URLs which were erroneously considered dead by the bot, you can report them with this tool.
  • If you found an error with any archives or the URLs themselves, you can fix them with this tool.

Cheers.—cyberbot IITalk to my owner:Online 22:12, 28 February 2016 (UTC)[reply]

UN 1863

[edit]

I removed the following sentence from the section "Differences between Jet A and Jet A-1"

As with Jet A-1, Jet A can be identified in trucks and storage facilities by the [[UN number]] 1863 [[Dangerous goods|Hazardous Material]] placards.<ref>
{{cite web
 | title= U.S. Department of Transportation 2008 Emergency Response Guide (ERG)
 | author= U.S. DOT
 | url= http://wwwapps.tc.gc.ca/saf-sec-sur/3/erg-gmu/erg/idindex.aspx?page=15
}}
</ref>

I think, what was meant, is, that both fuels are designated by that number. But I don't know, and the given source doesn't relly prove anything to a layman. At any rate, a section "Differences..." should not have a sentence starting with "As with". Please can anyone in the know add the correct UN-Number information back into the article? If it's the same for both types of fuel, it needs to go into the parent section. If not, the different number needs to be found out, and the two numbers put into the two subsections, in sentences with unambiguous wording, thankyouverymuch. --BjKa (talk) 10:44, 19 May 2016 (UTC)[reply]

[edit]

Hello fellow Wikipedians,

I have just modified 2 external links on Jet fuel. Please take a moment to review my edit. If you have any questions, or need the bot to ignore the links, or the page altogether, please visit this simple FaQ for additional information. I made the following changes:

When you have finished reviewing my changes, please set the checked parameter below to true or failed to let others know (documentation at {{Sourcecheck}}).

This message was posted before February 2018. After February 2018, "External links modified" talk page sections are no longer generated or monitored by InternetArchiveBot. No special action is required regarding these talk page notices, other than regular verification using the archive tool instructions below. Editors have permission to delete these "External links modified" talk page sections if they want to de-clutter talk pages, but see the RfC before doing mass systematic removals. This message is updated dynamically through the template {{source check}} (last update: 5 June 2024).

  • If you have discovered URLs which were erroneously considered dead by the bot, you can report them with this tool.
  • If you found an error with any archives or the URLs themselves, you can fix them with this tool.

Cheers.—InternetArchiveBot (Report bug) 15:59, 16 July 2016 (UTC)[reply]

[edit]

Hello fellow Wikipedians,

I have just modified 5 external links on Jet fuel. Please take a moment to review my edit. If you have any questions, or need the bot to ignore the links, or the page altogether, please visit this simple FaQ for additional information. I made the following changes:

When you have finished reviewing my changes, please set the checked parameter below to true or failed to let others know (documentation at {{Sourcecheck}}).

This message was posted before February 2018. After February 2018, "External links modified" talk page sections are no longer generated or monitored by InternetArchiveBot. No special action is required regarding these talk page notices, other than regular verification using the archive tool instructions below. Editors have permission to delete these "External links modified" talk page sections if they want to de-clutter talk pages, but see the RfC before doing mass systematic removals. This message is updated dynamically through the template {{source check}} (last update: 5 June 2024).

  • If you have discovered URLs which were erroneously considered dead by the bot, you can report them with this tool.
  • If you found an error with any archives or the URLs themselves, you can fix them with this tool.

Cheers.—InternetArchiveBot (Report bug) 00:18, 12 November 2016 (UTC)[reply]

[edit]

Hello fellow Wikipedians,

I have just modified 5 external links on Jet fuel. Please take a moment to review my edit. If you have any questions, or need the bot to ignore the links, or the page altogether, please visit this simple FaQ for additional information. I made the following changes:

When you have finished reviewing my changes, you may follow the instructions on the template below to fix any issues with the URLs.

This message was posted before February 2018. After February 2018, "External links modified" talk page sections are no longer generated or monitored by InternetArchiveBot. No special action is required regarding these talk page notices, other than regular verification using the archive tool instructions below. Editors have permission to delete these "External links modified" talk page sections if they want to de-clutter talk pages, but see the RfC before doing mass systematic removals. This message is updated dynamically through the template {{source check}} (last update: 5 June 2024).

  • If you have discovered URLs which were erroneously considered dead by the bot, you can report them with this tool.
  • If you found an error with any archives or the URLs themselves, you can fix them with this tool.

Cheers.—InternetArchiveBot (Report bug) 03:36, 22 April 2017 (UTC)[reply]

[edit]

Hello fellow Wikipedians,

I have just modified 4 external links on Jet fuel. Please take a moment to review my edit. If you have any questions, or need the bot to ignore the links, or the page altogether, please visit this simple FaQ for additional information. I made the following changes:

When you have finished reviewing my changes, you may follow the instructions on the template below to fix any issues with the URLs.

This message was posted before February 2018. After February 2018, "External links modified" talk page sections are no longer generated or monitored by InternetArchiveBot. No special action is required regarding these talk page notices, other than regular verification using the archive tool instructions below. Editors have permission to delete these "External links modified" talk page sections if they want to de-clutter talk pages, but see the RfC before doing mass systematic removals. This message is updated dynamically through the template {{source check}} (last update: 5 June 2024).

  • If you have discovered URLs which were erroneously considered dead by the bot, you can report them with this tool.
  • If you found an error with any archives or the URLs themselves, you can fix them with this tool.

Cheers.—InternetArchiveBot (Report bug) 15:06, 9 September 2017 (UTC)[reply]

[edit]

Hello fellow Wikipedians,

I have just modified 6 external links on Jet fuel. Please take a moment to review my edit. If you have any questions, or need the bot to ignore the links, or the page altogether, please visit this simple FaQ for additional information. I made the following changes:

When you have finished reviewing my changes, you may follow the instructions on the template below to fix any issues with the URLs.

This message was posted before February 2018. After February 2018, "External links modified" talk page sections are no longer generated or monitored by InternetArchiveBot. No special action is required regarding these talk page notices, other than regular verification using the archive tool instructions below. Editors have permission to delete these "External links modified" talk page sections if they want to de-clutter talk pages, but see the RfC before doing mass systematic removals. This message is updated dynamically through the template {{source check}} (last update: 5 June 2024).

  • If you have discovered URLs which were erroneously considered dead by the bot, you can report them with this tool.
  • If you found an error with any archives or the URLs themselves, you can fix them with this tool.

Cheers.—InternetArchiveBot (Report bug) 02:20, 25 November 2017 (UTC)[reply]

[edit]

Hello fellow Wikipedians,

I have just modified 2 external links on Jet fuel. Please take a moment to review my edit. If you have any questions, or need the bot to ignore the links, or the page altogether, please visit this simple FaQ for additional information. I made the following changes:

When you have finished reviewing my changes, you may follow the instructions on the template below to fix any issues with the URLs.

This message was posted before February 2018. After February 2018, "External links modified" talk page sections are no longer generated or monitored by InternetArchiveBot. No special action is required regarding these talk page notices, other than regular verification using the archive tool instructions below. Editors have permission to delete these "External links modified" talk page sections if they want to de-clutter talk pages, but see the RfC before doing mass systematic removals. This message is updated dynamically through the template {{source check}} (last update: 5 June 2024).

  • If you have discovered URLs which were erroneously considered dead by the bot, you can report them with this tool.
  • If you found an error with any archives or the URLs themselves, you can fix them with this tool.

Cheers.—InternetArchiveBot (Report bug) 06:45, 23 January 2018 (UTC)[reply]

Minor Quibles

[edit]
Comparing avgas to jet fuel had errors. Volatility is not the reason high performance aircraft engines require high octane gasoline. High performance high efficiency engines have high compression ratios, and octane rating involves preventing hot fuel air mixture (in carbureted engines) from igniting (see autoignition) in the cylinder before the spark, either by using more stable fuel like isooctane, or an additive like Tetra Ethyl Lead or Benzene or alcohol to capture heat generated free radicals before chain reaction (overcoming inhibition) is initiated by spark. German WW2 propeller driven fighters used fuel injection which allowed lower octane fuel.
Kerosene was used originally because gas was in short supply (higher cost)and early jets were not fuel efficient so kerosene (a lower grade of Diesel)was used. Diesel engines inject fuel at the top of the compression cycle (air being superheated to ~500F which is higher than the autoignition temperature of diesel/kerosene. Similarly jet fuel's lower autoignition temp causes it to combust on entering the hot combustion temperature. Also note that Diesel/Kerosene has a higher energy per pound of fuel, alcohol has a lower energy per pound than gasoline.
Kerosene is a wide boiling point mixture as is Deisel #1 fuel and they contain waxy paraffins, which provide lubrication. The Sulfur compounds (and Nitrogen compounds) in the fuel have no bearing on lubricity of the fuel. Sulfur acids creating on burning can cause corrosion of engines.
NOx or Nitrogen Oxides are created at high temperatures and high compression ratios. The only way to lower NOx from diesel trucks is Urea injection etc. Nothing much that the fuel can accomplish. No jet fuel manufacturers currently add lower chain amines to reduce NOx.

Shjacks45 (talk) 05:03, 7 September 2018 (UTC)[reply]

Synthetic/Biofuels Sections Are Severely Dated

[edit]

I know no editor likes people popping in and saying "this page sucks" before they walk away, but I was using this page as background research on a USAF project and the Synthetic jet fuel, USAF synthetic fuel trials, and Jet biofuels sections are terribly out of date. Many statements/sentences are of the "this is happening now" type and they are talking about something that happened in 2008 or 2010 or that have been completely overcome by events and aren't true.

Possible solutions are including the date/year of the happening with the information such as in the Jet biofuels section "In 2010, British Airways and Velocys have entered into a partnership in the UK to design a series of plants that convert household waste into jet fuel."

Alternatively, there are several statements like "The Pentagon hopes to reduce its use of crude oil from foreign producers and obtain about half of its aviation fuel from alternative sources by 2016." This is three years out of date so it should be stated that they met the goal or the whole sentence should be deleted.

My 2 cents. Ckruschke (talk) 13:44, 2 May 2019 (UTC)Ckruschke[reply]

Contradictory lubricity statements

[edit]

"However, jet fuel tends to have poor lubricating ability in comparison to diesel, which increases wear in fuel injection equipment.[citation needed] An additive may be required to restore its lubricity. Jet fuel is more expensive than diesel fuel but the logistical advantages of using one fuel can offset the extra expense of its use in certain circumstances.

Jet fuel contains more sulfur, up to 1,000 ppm, which therefore means it has better lubricity and does not currently require a lubricity additive as all pipeline diesel fuels require."

Which is right ? — Preceding unsigned comment added by 109.144.208.199 (talk) 23:24, 1 July 2023 (UTC)[reply]

NFPA Fire Hazard diamond sign

[edit]

Article shows 2 2 0

I believe it should be 0 2 0

https://rivcoeh.org/sites/g/files/aldnop361/files/migrated/Portals-0-PDF-HazMat-bep-nfparatings.pdf

Rcscruffy (talk) 19:58, 31 July 2024 (UTC)[reply]