Talk:Perfboard

Electronics Mid‑importance

	Electronics portal This article is part of WikiProject Electronics, an attempt to provide a standard approach to writing articles about electronics on Wikipedia. If you would like to participate, you can choose to edit the article attached to this page, or visit the project page, where you can join the project and see a list of open tasks. Leave messages at the project talk pageElectronicsWikipedia:WikiProject ElectronicsTemplate:WikiProject Electronicselectronic articles
Mid	This article has been rated as Mid-importance on the project's importance scale.

Untitled[edit]

What's perf? --Abdull 14:39, 15 March 2007 (UTC)[reply]

I assumed it meant "perforated", but I guess that's not necessarily the reason. — Omegatron 15:04, 31 March 2007 (UTC)[reply]

Donut board[edit]

Does anyone know if this is what is called donut veroboards or donut boards in Malaysia and some other countries Nil Einne 11:42, 21 June 2007 (UTC)[reply]

Stub[edit]

Isn't this page a stub? If it is, can someone put the tag because I don't know how to. ☺Efansay^T/_C☺ 07:44, 3 July 2007 (UTC)[reply]

No mention of better perf boards[edit]

Firstly, perfboard is any kind of perforated board. For instance, the perforated particle board that is used for, for instance, hanging tools in a tool shop, is a kind of perfboard.

Small-scale perfboards can be used for assembling electronic circuits. Such a board provides a backing substrate to which electronic components are fastened. However, it provides no electrical connections. The article describes only this type of perfboard. This product is next to useless, because even though it has copper, that provides little value: all that the copper pads do is mechanically fasten each the component to the board (for which purpose glue from a glue gun can be used, with a perf-board that has no copper pads). No current ever flows through the solder!

For one-off, small-scale, or hobby production of electronic circuits, there exist printed circuit boards that have conducting traces spanning groups of two, three or more solderpads, and even some long runs that are intended for uses like power rails, ground or some other global use. With these types of boards, one can build neat circuits with no external wire wrapping. With well planned component placement, the result can be almost as good as a custom PC board. When a wire connection must be made, it can often be installed as a zero-ohm resistor: it is inserted into holes from the component side, soldered on the copper side, and clipped, rather than installed as a bridge between component leads. Some such boards have places to put generic integrated circuits (even surface-mounted ones), and some have edge pins for inserting into slot connectors, like ISA buses and such.

Given that such boards are available, it is foolish to even think about the no-connection perfboards. They are inferior even for prototyping, and do not cost significantly less. Basically they just have more copper removed, causing all of the pads to be isolated, rather than leaving some copper in place for connections.

Breadboards are much better for experimentation and prototyping, and printed circuit perf boards exist that have similar layouts to breadboards, so that experimental breadboard layouts can be translated directly to printed circuits. Between these two needs, there is no real middle space that is satisfied by boards that have no connections between pads.

The article should mention these other kinds of boards. — Preceding unsigned comment added by 192.139.122.42 (talk) 00:01, 21 July 2011 (UTC)[reply]

"Given that such boards are available, it is foolish to even think about the no-connection perfboards. They are inferior even for prototyping, and do not cost significantly less." I must be doing something wrong then.

"The article should mention these other kinds of boards.", these have other names and thus other articles Veroboard, Breadboard --2003:C0:6BC0:CCC1:C646:19FF:FE21:1D1D (talk) 10:50, 19 November 2015 (UTC)[reply]

perfboard without copper[edit]

Perfboard without copper is useful. You can not use clad perfboard for an optoisolator circuit which requires a large creepage distance under the isolator. For this you want FR4 without any copper, something like this:

Vectorbord® Part Number : 84P44WE 4.5" W x 8.5" L ... 0.042" Hole Dia. ....FR4 Epoxy Glass ... Unclad Punchbord http://www.vectorelect.com/Product/Vectorbord/84P44WE.htm

— Preceding unsigned comment added by 76.90.10.170 (talk • contribs) 03:56, 29 June 2014 (UTC)[reply]

Requested move 17 March 2016[edit]

The following is a closed discussion of a requested move. Please do not modify it. Subsequent comments should be made in a new section on the talk page. Editors desiring to contest the closing decision should consider a move review. No further edits should be made to this section.

The result of the move request was: no consensus to move (non-admin closure). SSTflyer 12:32, 5 April 2016 (UTC)[reply]

Perfboard → Matrix board – Perfboard is perforated PCB material but without any copper. This article refers to board with copper pads. Matrix board is perfboard with copper pads. Rob Kam (talk) 20:29, 17 March 2016 (UTC) relisted --SST flyer 15:36, 25 March 2016 (UTC)[reply]

Oppose - My search for perfboard is showing boards with and without copper (mostly with). Perfboard wins a Google fight. ~Kvng (talk) 00:24, 29 March 2016 (UTC)[reply]

The above discussion is preserved as an archive of a requested move. Please do not modify it. Subsequent comments should be made in a new section on this talk page or in a move review. No further edits should be made to this section.