Talk:Pica (typography)
![]() | This ![]() It is of interest to the following WikiProjects: | ||||||||||
|
![]() | This article is written in American English, which has its own spelling conventions (color, defense, traveled) and some terms that are used in it may be different or absent from other varieties of English. According to the relevant style guide, this should not be changed without broad consensus. |
Article is wrong
[edit]There are more than 152 points in an inch, and 6 picas do not equal an inch. The metric equivalents are therefore off as well. You can look at any "pica pole," a form of ruler that most frequently displays both inches and picas with half-pica (6-point) increments also marked, the difference is quite noticeable at 12 inches, nearly 6 extra points. You can also check Webster's Unabridged (3rd ed.), where the pica is defined as "about 1/6 inch." See also OnlineConversion.com (1 inch equals 72.571428571 points, not 72 points even).
The misinformation in the article flows from a decision made by the designers of PostScript to ignore an established standard. PostScript does away with the small change and treats an inch as containing 72 points. The information is accurate only for PostScript-based typography systems. E.g., the TeX-based typesetting programs use 72.270000003 points to the inch. Ibid. There is also an obsoleted "Didot" point system that was widely used in Europe until the metric system gained ascendancy. "Pica" is also used as a unit of measure on typewriters, where it indicates a typeface with 10 characters per horizontal inch. That is in contrast to "elite" typewriter spacing which is 12 characters per inch.
The idea that 6 picas or 72 points equals an inch is either a mere approximation or specific to Postscript (your choice), not an accurate calculation based on the standard, except in the PostScript world. (I note that the article's final paragraph on markup conventions is PostScript-specific; it assuredly is not the markup used historically in the printing industry.) Anyone who has composed large pages in hot type (e.g., newspaper pages) knows that the approximation becomes more and more useless as the dimension of the composition area increases. That is why typographers do/did their calculations in picas and points rather than inches. Unfortunately, the misinformation has propagated across the Net. (Try Google for "picas per inch," a powerful testament to the power of historical revisionism by the computer industry.)
You can find an overview of the point's (and pica's) generally accepted history at this site. But see Father Truchet, the typographic point, Romain du roi, and tilings (PDF) (arguing that Truchet rather than Fournier should be credited with creating the point).
I note that the misinformation is spreading on Wikipedia. See WYSIWYG ("72 PPI came from the standard of 72 'points' per inch used in the commercial printing industry").
This is important; we are discussing a standard that was unchanged for more than a hundred years until PostScript came along.
Someone with time needs to research and rewrite this article
-Marbux
- I haven't written the detailed history that's needed, but I've corrected the factual inaccuracy and mentioned PostScript. Maybe the article could be retagged for expansion. Regarding the "pica" on typewriters: IMO it is plausible that a typewriter font at 10 characters/inch might have a line height of one pica. Seahen 16:05, 19 February 2006 (UTC)
- "When Adobe created the PostScript standard..." would be much more appropriate than "A corporation proposing the PostScript standard..."
- PostScript seldom if ever refers to ‘picas’, but refers to its unit of 1/72" as a point sometimes, as in the Blue Book, p.36: “Remember that a point is 1/72 inch.”. So I have removed the erroneous statement about PostScript and picas. --scruss (talk) 00:51, 17 September 2015 (UTC)
SI units?
[edit]Can anyone substitute or at least add the corresponding values in SI units? --Mecanismo 18:06, 9 October 2005 (UTC)
- Wouldn't make much sense to substitute, since the pica is defined as being a sixth of an inch, but I've added the approximate millimeter equivalent. Factitious 20:05, 10 October 2005 (UTC)
abbreviation
[edit]Cascading Style Sheets use 'pc' for the abbreviation for pica. Jim albright (talk) 18:01
Pronunciation
[edit]I'm torn. On the one hand, WP:NOTDICTIONARY, Wiktionary, and IPA's always an unpleasant eyesore. On the other, this is a rather obscure pronunciation: pikachu and its French origin are going to point some readers towards reading it /pikə/ and situations like that are the one occasion where pronunciation guides are in order.
The problem is the current article is wrong. It's /ˈpaɪkə/ in American English but /ˈpʌɪkə/ in the UK per the OED's "pica, n²". Personally, I'd rather leave it to the Wiktionary entry rather than have two separate pronunciations here, but what do you guyls think? — LlywelynII 15:25, 30 April 2015 (UTC)
Pica symbol
[edit]Hi, I'm Francesco from Italian Wikipedia. We checked on the web and in technical literature but we can't find any references to P with an overlaid slash () like described in the article. It maybe a vandalism of user Picaman, who wrote the thing. The only symbol we found is a square with a overlaid slash () on this spanish site. I saw the same symbol was used in United States customary units in the form P/, we did't found this form too. So be careful to propagate this unsure symbol--Frank50 s (talk) 16:44, 28 June 2015 (UTC)
- Start-Class vital articles
- Wikipedia level-5 vital articles
- Wikipedia vital articles in Physical sciences
- Start-Class level-5 vital articles
- Wikipedia level-5 vital articles in Physical sciences
- Start-Class vital articles in Physical sciences
- Start-Class Typography articles
- Mid-importance Typography articles
- Wikipedia articles that use American English