Jump to content

Talk:Shielded metal arc welding

Page contents not supported in other languages.
From Wikipedia, the free encyclopedia
Former featured articleShielded metal arc welding is a former featured article. Please see the links under Article milestones below for its original nomination page (for older articles, check the nomination archive) and why it was removed.
Main Page trophyThis article appeared on Wikipedia's Main Page as Today's featured article on February 16, 2006.
Article milestones
DateProcessResult
January 21, 2006Peer reviewReviewed
January 26, 2006Featured article candidatePromoted
October 25, 2020Featured article reviewDemoted
Current status: Former featured article

Old talk

[edit]

It says "these face shields sense when the super-bright electric arc has begun and turn the liquid crystal glass dark a few nanoseconds later." But switching speeds of liquid crystals are usually more in the millisecond time scale. Of course for the welding application it doesn't have to be a problem, since the light from the arc will presumably not turn on in a nanosecond, but more gradually.

Fixed. --Spangineeres (háblame) 03:23, 14 January 2006 (UTC)[reply]


Wasn't this already on the main page a while back? A Clown in the Dark 03:06, 16 February 2006 (UTC)[reply]

Nope, but Welding and Gas metal arc welding were last year. This one just got featured last month. --Spangineer (háblame) 03:08, 16 February 2006 (UTC)[reply]

When I was learning about welding in the 1980's we learned about synergic power supplies, where pulsed current carries particles from the electrode onto the work in a very controlled fashion. Unless I remember wrongly, welding power supplies can be much more sophisticated than the article describes. Dunstan 13:49, 16 February 2006 (UTC)[reply]

They can be, but I think that's a topic for welding power supply. I haven't done much study of all of the various types of power supplies and thus haven't written an in depth article on that topic. This article attempts to cover the basics of power supplies commonly used for SMAW, but I'll see if I can find anything in my sources about what you describe. --Spangineer (háblame) 16:18, 16 February 2006 (UTC)[reply]

Slag

[edit]

Why is it necessary to remove the slag? 74.109.213.249 (talk) 04:31, 15 December 2015 (UTC)[reply]

The main reason is that stick electrodes are short, thus too small to build up most welds in one pass. Multi-passing multiple electrodes to build up a single homogeneous weld bead needs the slag removed after each pass, otherwise the slag left would form a weak non-metallic layer in the weld. NDT examination of high-quality welds afterwards is often about looking for such pieces of included slag.
The problem of slag also led to the development of one-pass welding techniques such as firecracker welding or gas-shielded welding such as MIG / GMAW Andy Dingley (talk) 11:05, 15 December 2015 (UTC)[reply]

Electrode sources

[edit]

The last paragraph of the Electrode section was changed from:

Common electrodes include the E6010, a fast-freeze, all-position electrode with a minimum tensile strength of 60 ksi (410 MPa) which is operated using DCEP. Its cousin E6011 is similar except that it is used with alternating current. E7024 is a fast-fill electrode, used primarily to make flat or horizontal welds using AC, DCEN, or DCEP. Examples of a fill-freeze electrodes are the E6012, E6013, and E7014, all of which provide a compromise between fast welding speeds and all-position welding.<ref>Lincoln Electric, 6.2-7–6.2-10</ref>

to

Common electrodes include the E6010, a fast-freeze, all-position electrode with a minimum tensile strength of 60 ksi (410 MPa) which is operated using DCEP. E6010 is primarily used for making the root pass when welding pipe. Its cousin E6011 is similar except that it is used with alternating current. E6011 is known for its strong penetration and tolerance of dirty and/or rusty metal. E7018 is a low-hydrogen electrode used for high quality X-ray welds. It can be used in all positions with either AC or DC current. E7018 is also used when weld bead apeparance is a priority. E7024 is a fast-fill electrode, used primarily to make flat or horizontal welds using AC, DCEN, or DCEP. Examples of a fill-freeze electrodes are the E6012, E6013, and E7014, all of which provide a compromise between fast welding speeds and all-position welding.<ref>Lincoln Electric, 6.2-7–6.2-10</ref> E8018 and E9018 are higher strength electrodes commonly used on medium to high alloy steels, such as boilers.

All the added statements need to be confirmed in published works before being included here (as per WP:V). I'll look into the material I have, but any help would be appreciated! --Spangineeres (háblame) 18:20, 23 October 2006 (UTC)[reply]

I'll take a look in my books but the information is correct. To not even mention 7018 is odd especially when lesser known/used electrodes are mentioned. 6011 and 7018 are among the most commonly used electrodues. Pipe welds are typically done with a 6010 root pass and 7018 cap. Boiler tube welds are now commonly tig'ed for the root past and finished with the appropriate stick electrode (7018, 8018, or 9018). An picture of an electrode chart from Lincoln, or Miller/Hobart would not be a bad idea. (ROBZZZ 15:20, 24 October 2006 (UTC))[reply]

I fixed a slight grammar problem, changing "Examples of a fill-freeze electrodes" to "Examples of fill-freeze electrodes." Hildenja 05:53, 24 November 2006 (UTC)[reply]

How can a featured article on SMAW not mention E7018, which is perhaps the most commonly used electrode. 170.119.0.39 (talk) —Preceding undated comment added 08:32, 16 October 2010 (UTC).[reply]

Featured article status

[edit]

This article was on a list of potentially under-cited articles that may need to go to Wikipedia:Featured article review. I've added some "citation needed" tags in obvious places, though there may be more claims lacking references inside paragraphs. Major contributors for notification purposes: User:Spangineer, User:Triddle, User:Darth Panda, User:Mouston, User:Thomasnetrpm. -- Beland (talk) 01:59, 1 February 2020 (UTC)[reply]

Smaw

[edit]

Shielded metal arc 180.191.160.95 (talk) 03:35, 31 August 2022 (UTC)[reply]

Smaw

[edit]

What the history of electric arc welding and job opportunities 222.127.227.247 (talk) 10:34, 30 July 2024 (UTC)[reply]