User talk:Eas4200c.f08.nine.s
Group nine - Week 1
Aircraft Design
[edit]Airplanes are composed of many different parts, the main structural ones being the wing and the fuselage. The wing and fuselage are made up of many basic structural elements, and those elements act like beams in a torsion member. One main difference between beams and aircraft structural elements is that aircraft loads are in the form of air pressure and concentrated loads such as in the landing gear and passenger seats. As an engineer we have to decide if these local loads are not excessive enough to cause major deflections.
Aircraft Structure
[edit]The main structural purpose of the wing is to transfer the load to the fuselage. The airfoil shape of the wing is based on aerodynamics considerations and will not be discussed in this article, which focuses on the structural components of the wing. The wing acts like a beam and torsion member. The wing is composed mainly spars and ribs. "The spar is a heavy beam running from span wise to take transverse shear loads and span wise bending. It is usually composed of a thin shear panel, or web, with a heavy cap or flange at the top and bottom to take bending." [1] There may be more than one spar in a wing, but in general one carries the majority of the forces on it, and is called the main spar. The wing ribs are flat structures that are used to take in-plane loads which reduce the effective buckling length of the stringers and as a result it increases their compressive load capability. Ribs are placed chord wise and they are supported by the spars. [2]
A combination of using spars with or without stringers, thin or thick wing skin, thin or regular airfoils and stringers being manufactured or not as an inegral part of the skin depends on the design characteristics of the wing. It varies according to need and performance.
The skin of the fuselage bears the shear stresses due to the torques and traverse forces. It also carries the hoop stresses due to internal pressures of the aircraft.
The stabilator of an aircraft acts as a horizontal stabilizer and elevator. Stabilators are found on the back portion of the wings and allows the pilot to have a higher pitching moment.
Fuselage Designs
[edit]![](http://upload.wikimedia.org/wikipedia/commons/thumb/7/7c/Chapter_1_img_26.jpg/220px-Chapter_1_img_26.jpg)
Monocoque is a single shell design.
Semi-Monocoque is a single shell design that has stiffening braces.
Aircraft Materials
[edit]Aircraft materials must be of high strength and stiffness while remaining lightweight. The typical types of metals that are used tend to be steel alloys, titanium, aluminum, and fiber-reinforced composites. Aluminum is a very attractive metal for use as an aircraft material because it is very light weight and although not as strong as steel and titanium alloys, it is sufficient to withstand the shearing loads on the fuselage of an aircraft. The 2024-T3 aluminum alloy is a common material used for the fuselage and lower wing skins. These areas are prone to fatigue and cyclic tensile stresses and that is why a stronger alloy used. The upper wing, however, uses a 7075-T6 alloy which has a higher strength and lower fracture toughness. The upper wing experiences less fatigue and that is why it is used. Carbon fiber is a non-metallic material that is used in aircraft design due to its high strength and extremely low weight. "Fiber composites are stiff, strong, and light and are thus most suitable for aircraft structures." [3]
Landing Gear
[edit]The landing gear of an aircraft is what makes it possible for an aircraft to take off and land. The landing gear commonly consists of a high strength steel alloy because of the extreme stresses that are experienced during take off and landing. In general, wheels are the main component in the landing gear, but other gear such as skis or floats may be used.
Finite Element Method
[edit]The finite element method (FEM) is "a numerical technique for finding approximate solutions of partial differential equations (PDE) as well as of integral equations. The solution approach is based either on eliminating the differential equation completely (steady state problems), or rendering the PDE into an approximating system of ordinary differential equations, which are then solved using standard techniques such as Euler's method, Runge-Kutta, etc."[4]
FEM is used often in most fields of Engineering. Partial differential equations are used in the designing of aerospace structures for example, and as a result the finite element method is used to simplify these functions for Aerospace Engineers. FEM is widely used for stiffness and strength visualizations, as well as reducing weight, material, and costs for certain projects. It can also be used to pin point where structures may bend or twist, and determine the distribution of stresses and displacements.[5]
Stress and Strain
[edit]![](http://upload.wikimedia.org/wikipedia/commons/thumb/0/00/Stress_v_strain_A36_2.png/180px-Stress_v_strain_A36_2.png)
1. Ultimate Strength
2. Yield Strength
3. Rupture
4. Strain hardening region
5. Necking region.
Stress and Strain are engineering terms that refer to a force per unit area, and the amount of deformation on an object caused by that stress respectively. Stress and Strain are proportional by a factor known as the "Young's Modulus". This quantity relates directly to an objects stiffness; the higher the modulus, the higher the stiffness.
The Equation is read as "Stress is equal to Young's Modulus times Strain.
References
[edit]- ^ C. T. Sun. Mechanics of Aircraft Structures 2nd Edition Pg.10 New York: John Wiley & Sons, 2006.
- ^ Source: http://www.jrotc.org/images/spar.gif
- ^ C. T. Sun. Mechanics of Aircraft Structures 2nd Edition Pg.16 New York: John Wiley & Sons, 2006.
- ^ "XJamRastafire" Wikipedia. 11 Sept 2008 <http://en.wikipedia.org/wiki/Finite_element_method/>.
- ^ "XJamRastafire" Wikipedia. 11 Sept 2008 <http://en.wikipedia.org/wiki/Finite_element_method/>.